前控制臂

Powerflex 黑色系列下臂外衬套“脚轮可调”

前控制臂外衬套配有轻质铝制可调节套管，可在车上调节脚轮，同样采用我们独特的聚氨酯衬套。



两套适用于两只下臂。
请注意，这些部件应由工程师安装。

Powerflex 黑色系列- 专为赛道设计 - 随时准备比赛 - 力求做到最好。

Powerflex 黑色系列衬套采用 95 Shore A 复合材料制成，可最大程度地控制底盘几何形状。这种复合材料的抗负载能力比标准橡胶高出 80%，硬度比我们的紫色高性能材料高出 25%。

如果您的要求纯粹是极致的操控性和底盘性能，那么 Powerflex Black 系列是独一无二的，可为您的底盘提供最精确、最准确的定位。

适合：
保时捷 987 Boxster 2006>>
保时捷 987C Cayman 2005>>
保时捷 997 2006>>

请点击“放大”来查看图表。
图表重新编号 13。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

PFF57-802BLK

您正在查看的产品与这些编号存在交叉引用关系

Powerflex 下臂外衬套“脚轮可调”

前控制臂外衬套配有轻质铝制可调节套管，可在车上调节脚轮，同样采用我们独特的聚氨酯衬套。

两套适用于两只下臂。
请注意，这些部件应由工程师安装。

适合：
保时捷 987 Boxster 2006>>
保时捷 987C Cayman 2005>>
保时捷 997 2006>>

请点击“放大”来查看图表。
图表重新编号 13。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

PFF57-802

您正在查看的产品与这些编号存在交叉引用关系

Powerflex 下臂后衬套“外倾角可调”

前控制臂内衬套采用耐用的不锈钢可调套筒进行外倾角调节，该套筒在我们独特的油脂保持聚氨酯衬套中运行。

两套适用于两只下臂。
请注意，这些部件应由工程师安装。

適用於:
保时捷 987 Boxster 2006>>
保时捷 987C Cayman 2005>>
保时捷 997 2006>>

请点击“放大”来查看图表。
图表重新编号 13。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

PFF57-801

您正在查看的产品与这些编号存在交叉引用关系

Powerflex Black Series Lower Arm Rear Bush "Camber Adjustable"

Front control arm inner bush gives the camber adjustment with its durable stainless steel adjustable sleeve which runs in our unique grease retaining polyurethane bush.

Set of 2 for TWO lower arms.
Please note these parts should be fitted by an engineer.

Powerflex Black Series - Designed for the Track - Ready to Race - Engineered to be the best.

Powerflex Black Series bushes are manufactured using a 95 Shore A compound to provide maximum control of chassis geometry. This compound can be up to 80% more resistant to load than standard rubber and 25% stiffer than our purple performance material.

If your requirements are purely for the ultimate in handling and chassis performance then Powerflex Black Series are unique, offering the most precise and accurate alignment for your chassis.

Fits:
Porsche 987 Boxster 2006>>
Porsche 987C Cayman 2005>>
Porsche 997 2006>>

Please click 'Zoom in' to view the diagram.
Diagram re No 13.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

PFF57-801BLK

您正在查看的产品与这些编号存在交叉引用关系

下叉臂中央衬套拆卸和安装工具。

需要 1 个工具

#大象赛跑#

适合
保时捷 986 Boxster -前部和后部
保时捷 987 Boxster 和 Cayman -前部和后部
保时捷 996 -前部和后部
保时捷 997 -前部和后部
保时捷 981 Boxster 和 Cayman -仅前部
保时捷 991 -仅正面

简化 Monoball 产品和更换衬套的安装过程。

我们的两件式杯形和活塞工具可轻松取出和插入衬套，无需拆卸轮架或控制臂。无需使用车间压力机。这些工具的设计精确贴合衬套周长，可防止衬套意外损坏并确保正确安装。

我们有用于 LCA 中央衬套、后直立 LCA 衬套和后直立减震器支架衬套的工具。

996、997、986、987 和 981 上的前后控制臂
前下控制臂仅适用于 991

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

2260019

您正在查看的产品与这些编号存在交叉引用关系

Lower control arm eccentric monoballs.
1 kit required per axle



Fits
Porsche 986 Boxster - Front and Rear
Porsche 987 Boxster and Cayman - Front and Rear
Porsche 996 - Front and Rear
Porsche 997 - Front and Rear
Porsche 981 - Front and Rear
Porsche 718 - Front and Rear
Porsche 991 - Front Only

Our Eccentric Control Arm Monoball Cartridges replace inner rubber bushings with spherical bearings, providing low friction and precisely holding camber settings.
The eccentric design allows increasing or decreasing camber, as needed.

Increasing Camber

Position the eccentric to maximize Lower Wishbone length, adding about .86 degree of negative camber on the 996/997 rear suspension, about .36 degree of negative camber on the Boxster rear suspension, and .39 degrees on the 996/997/Boxster front suspension.
Cost effective for cars that just want extra camber. For even more camber and ease of adjustment, see our GT3 type fully adjustable control arms.

Decreasing Camber

Position the eccentric to minimize Lower Wishbone length. Perfect for lowered cars that have too much negative camber and want to get back to factory camber settings to minimize tire wear on the street. Makes rear camber about .86 degrees more positive & front camber about .39 degrees positive for 996/997 while Boxsters will get about .39 degrees positive front and .36 degrees positive rear.



Made from hardened steel, plated and weather-sealed, these bearings are made to last. Fits the front or rear stock and GT3 type control arms.

Sized to fit factory original control arms. Not compatible with some aftermarket replacement control arms that use a larger non-stock size bushing.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

2260006

您正在查看的产品与这些编号存在交叉引用关系

BBi Autosport front/rear lower control arm kit for Porsche 996/997/991/987/981 except GT4
Fits cars with and without PASM



Features :

•   Improved two piece 996 GT3 lower control arm design
•   Stronger than cast motorsport Cup arms
•   Allows proper camber adjustment
•   Uses GT3 shims to adjust camber & lower control arm length (sold separately)
•   High-strength steel alloy spherical bearings, completely serviceable unlike the motorsports arms
•   Sealed monoball inner bearing
•   Allows easy access to inner arm hardware
•   Includes adjustable thrust arm bushings to adjust caster and wheelbase
•   A must have for all track and race enthusiast
•   Each kit includes pair of 2 arms
•   Fits both front and rear axles
•   Compatible with all 996/997/991/987/981 models except GT4

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

BBILOWRCNTRL9697

您正在查看的产品与这些编号存在交叉引用关系

Spacer kit for Eibach adjustable control arms 572610K.
This kit will allow the arms to be fitted onto cars with hydraulic bush.



PRICE IS FOR A SET OF 2.

Front or Rear Fitment:
Porsche 996
Porsche 986

Front Fitment only:
Porsche 997 GT2/GT3

Rear Fitment only:
Porsche 997 Carrera
Porsche 997 Turbo
Porsche 987
Porsche 981

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

5.72612K

您正在查看的产品与这些编号存在交叉引用关系

六角螺母 - M8 - 用于赛车控制臂。

单独出售；每只手臂需要 2 个。

工厂适配：
保时捷 996 GT2 2001-05
保时捷 996 GT3 1999-05
保时捷 997-1 GT2 2007-09
保时捷 997 GT3 2007-11

在以下保时捷车型上从标准控制臂升级到赛车控制臂时也需要这些垫圈：
保时捷 996 Carrera 1998-05
保时捷 996 Turbo 2001-05

图表参考 26。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

90007606402

您正在查看的产品与这些编号存在交叉引用关系

RSS Lower Control Arm Kit for Porsche Models .
Type: None Adjustable Thrust Arm Bushing



RSS Tarmac Series Motorsport Lower Control Arms are specifically engineered for use on lowered vehicles that have reduced travel struts/dampers such as PASM or M030 option. Alternatively if the car is equipped with high quality aftermarket or motorsport coilover kits ie Bilstein PSS10, KW V3 or Ohlins etc.

The Lower Control Arms are NOT COMPATIBLE with "Base Model Suspension" (long travel struts/dampers) or "Base Model struts/dampers with lowering springs."
Caution: Do not install on vehicles with Base Model struts/dampers as it may result in an unsafe driving condition with possibility of suspension bind when struts/dampers are fully extended or in full drop.

Price: Set of Two Control Arms plus 2 x 1mm/2mm/3mm/7mm Shims.

RSS Tarmac Series Control Arms are manufactured from 6061 aerospace grade billet aluminum. This allows for a more uniform molecular structure
at every point of the arm over the cast motorsports arm giving the customer a more durable and inherently stronger part. Manufacturing from billet
aluminum rather than casting results in less impurities in the metal.

• Completely serviceable - for the extreme, repetitive track-day participant, our high-strength steel alloy spherical bearings (with a friction reducing /longevity increasing Teflon liner) can be replaced unlike the motorsports arm, in which case the customer will have to buy a new set of arms if the spherical bearings are worn.
Additionally, anodized surfaces and zinc-plated steel parts allow for better corrosion resistance against the elements.

• Adjustable suspension geometry - adjust dynamic camber values and roll center heights with our unique zinc-plated steel bushings.

• Solid monoball control arm ends offer a more responsive suspension over the factory one-piece rubber-injected control arm (also uses the same high
strength steel alloy spherical bearing found in our control arm monoball kit).

• Unique design provides more gusseting over the motorsports arms for added strength and aesthetically appealing looks.

Please Check Fitting Guide Before Ordering Click Here

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

357

您正在查看的产品与这些编号存在交叉引用关系

RSS Lower Control Arm Kit for Porsche Models.
Type: None Adjustable Thrust Arm Bushing



RSS Tarmac Series Motorsport Lower Control Arms are specifically engineered for use on lowered vehicles that have reduced travel struts/dampers such as PASM or M030 option. Alternatively if the car is equipped with high quality aftermarket or motorsport coilover kits ie Bilstein PSS10, KW V3 or Ohlins etc.

The Lower Control Arms are NOT COMPATIBLE with "Base Model Suspension" (long travel struts/dampers) or "Base Model struts/dampers with lowering springs."
Caution: Do not install on vehicles with Base Model struts/dampers as it may result in an unsafe driving condition with possibility of suspension bind when struts/dampers are fully extended or in full drop.

Price: Set of Two Control Arms plus 2 x 1mm/2mm/3mm/7mm Shims.

RSS Tarmac Series Control Arms are manufactured from 6061 aerospace grade billet aluminum. This allows for a more uniform molecular structure
at every point of the arm over the cast motorsports arm giving the customer a more durable and inherently stronger part. Manufacturing from billet
aluminum rather than casting results in less impurities in the metal.

• Completely serviceable - for the extreme, repetitive track-day participant, our high-strength steel alloy spherical bearings (with a friction reducing /longevity increasing Teflon liner) can be replaced unlike the motorsports arm, in which case the customer will have to buy a new set of arms if the spherical bearings are worn.
Additionally, anodized surfaces and zinc-plated steel parts allow for better corrosion resistance against the elements.

• Adjustable suspension geometry - adjust dynamic camber values and roll center heights with our unique zinc-plated steel bushings.

• Solid monoball control arm ends offer a more responsive suspension over the factory one-piece rubber-injected control arm (also uses the same high
strength steel alloy spherical bearing found in our control arm monoball kit).

• Unique design provides more gusseting over the motorsports arms for added strength and aesthetically appealing looks.

Please Check Fitting Guide Before Ordering Click Here

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

358

您正在查看的产品与这些编号存在交叉引用关系

This mono ball bush fits to the back of the lower arm "coffin" arm



Fits:
Porsche 986 Boxster
Porsche 987 Boxster
Porsche 987C Cayman
Porsche 996 1998-04
Porsche 997
Porsche 991
Porsche 981 Boxster
Porsche 981 Cayman

Sealed Monoball Cartridges - Front and Rear - Most Porsche owners today, especially those of us who take our cars to the track, have equipped our cars with tires much wider and stickier than stock, which allows higher g-forces to be achieved in cornering and braking. During that type of hard driving, rubber suspension bushings are compressed and flexed by the extreme loads being put on them, defeating your car's finely tuned alignment settings, thereby reducing your braking and cornering potential. Mono balls are a downside-free improvement; because they eliminate four important sources of suspension slop without making your car's ride harsher. Your Porsche will handle and brake with greater precision, predictability, and feedback to the driver. Rennline mono balls are equipped with FK Motorsports bearings, cadmium-plated and Sealed to prevent premature wear due to moisture or dirt contamination, ensuring long track or street life.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

S18SETOF2

您正在查看的产品与这些编号存在交叉引用关系

CASTOR ADJUSTABLE THRUST ARM BUSHING KIT (For vehicles equipped with Non-Hydraulic Thrust Arm Bushings Only) for Porsche 986/996/997 GT2-3 & RS
SET OF 4. FRONT AXLE ONLY



The RSS Adjustable Thrust Arm Bushing Kit will improve handling and response of the suspension system and allows for additional caster adjustments. Eliminates unwanted caster changes in both front and rear suspension under acceleration and deceleration

AVAILABLE FOR PORSCHE® 986, 996 & 997 GT3/RS, RS 4.0 & GT2/RS PLEASE NOTE YOUR YEAR MAKE & MODEL IN COMMENTS SECTION.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

318

您正在查看的产品与这些编号存在交叉引用关系

RSS TARMAC SERIES XL (Extra Long) 2-PIECE COMPLETE LOWER CONTROL ARM KIT - Front Axle (Pair of 2).



RSS Tarmac Series Motorsport Lower Control Arms are specifically engineered for use on lowered vehicles that have reduced travel struts/dampers such as PASM or M030 option. Alternatively if the car is equipped with high quality aftermarket or motorsport coilover kits ie Bilstein PSS10, KW V3 or Ohlins etc.

The Lower Control Arms are NOT COMPATIBLE with "Base Model Suspension" (long travel struts/dampers) or "Base Model struts/dampers with lowering springs."
Caution: Do not install on vehicles with Base Model struts/dampers as it may result in an unsafe driving condition with possibility of suspension bind when struts/dampers are fully extended or in full drop.

Fits:
FOR FRONT AXLE PORSCHE 986, 996, 997 GT3/RS, 997 GT2/RS

Includes:
- Adjustable/Non-Hydraulic Replacement Thrust Arm Bushings,
- 1mm/2mm/3mm/7mm Shims,
- Spherical Monoball Ends.

RSS Tarmac Series Motorsport Lower Control Arms are specifically engineered for use on lowered vehicles that have reduced travel struts/dampers If you need assistance in identifying your suspension type please contact us. For specific fitment information refer to the "Chassis Fitment Guide and Lower Control Arm Fitment Notes" (See Images Below).

The RSS Tarmac Series – Motorsports Control Arms are designed for the Porsche driver who demands the absolute maximum in precision handling, feedback and control from their chassis. This system has been specially engineered to provide unmatched performance, quality, strength and serviceability. RSS Tarmac Series Control Arms address the performance related shortcomings of the OEM rubber mounted suspension components which were designed to reduce road noise and vibration for everyday street use. The use of rubber injected moldings in mounting components such as the control arms, thrust arms, upper links and toe arms is a compromise in regards to maximum suspension performance. The soft rubber deflects under suspension load which in turn causes unwanted movement (deflection) between the suspension and chassis. Data also shows that temporary changes in spring rates can occur as well. These movements and changes result in unnecessary corrections and inputs from the driver.

FEATURES & BENEFITS:
• Replaceable Sub-Assemblies: For the extreme, repetitive track day enthusiast or racer, our high strength
steel alloy spherical bearings (with a friction reducing, longevity increasing Teflon liner) outer and inner arm sub-assemblies can be replaced
unlike the motorsports arms, in which case a new set of arms will need to be purchased if the
spherical bearings are worn out.
• Adjustable Suspension Geometry: Adjust dynamic camber values and roll center heights with our
unique zinc plated steel bushings.
• Solid Monoball Control Arm Ends: Offers better handling and a more responsive suspension over the
factory one-piece rubber injected control arm by eliminating bushing deflection (also uses the same
high strength steel alloy spherical bearing found in our control arm monoball kit).
• 6061 Aerospace Grade Billet Aluminum Construction: Allows for a more uniform molecular structure
at every point of the arm over the cast components providing a more durable and inherently
stronger part. Manufacturing from billet aluminum rather than casting results in fewer impurities in
the metal.
• Anodized Aluminum Surfaces and Zinc Plated Steel Parts: Allows for better corrosion resistance
against the elements.

AVAILABLE FOR MOST PORSCHE 996, 986, 981, 982, 987 & 997 MODELS INCLUDING TURBO, GT2, GT2RS, GT3 & GT3RS.

RSS TARMAC SERIES Motorsports Suspension Kits have been winning championships and races in various forms of motorsport (Road Racing to Rally) around the world. RSS is the suspension of choice of professional race teams, tuners, track day junkies, and driving enthusiasts around the world.
- 2015 PIRELLI WORLD CHALLENGE TC CHAMPIONS
- 2014 FIA SPANISH RALLY TARMAC CHAMPIONS
- 2013 ROLEX GRAND-AM GX CHAMPIONS

RSS High Performance Tarmac Series Suspension Components are designed, engineered and manufactured on location here in the USA.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

373

您正在查看的产品与这些编号存在交叉引用关系

RSS TARMAC SERIES 2-PIECE COMPLETE LOWER CONTROL ARM KIT - Front Axle (Pair of 2).



RSS Tarmac Series Motorsport Lower Control Arms are specifically engineered for use on lowered vehicles that have reduced travel struts/dampers such as PASM or M030 option. Alternatively if the car is equipped with high quality aftermarket or motorsport coilover kits ie Bilstein PSS10, KW V3 or Ohlins etc.

The Lower Control Arms are NOT COMPATIBLE with "Base Model Suspension" (long travel struts/dampers) or "Base Model struts/dampers with lowering springs."
Caution: Do not install on vehicles with Base Model struts/dampers as it may result in an unsafe driving condition with possibility of suspension bind when struts/dampers are fully extended or in full drop.

Fits front axle Porsche 987, 997/991 C2, C4, Turbo, 981/982/718

Includes:
- Adjustable/Non-Hydraulic Replacement Thrust Arm Bushings,
- 1mm/2mm/3mm/7mm Shims,
- Spherical Monoball Ends.
** Note: 981 and 991 Models may require additional Front Litronic or Torque Vector Sensor Brackets.

The RSS Tarmac Series – Motorsports Control Arms are designed for the Porsche driver who demands the absolute maximum in precision handling, feedback and control from their chassis. This system has been specially engineered to provide unmatched performance, quality, strength and serviceability. RSS Tarmac Series Control Arms address the performance related shortcomings of the OEM rubber mounted suspension components which were designed to reduce road noise and vibration for everyday street use. The use of rubber injected moldings in mounting components such as the control arms, thrust arms, upper links and toe arms is a compromise in regards to maximum suspension performance. The soft rubber deflects under suspension load which in turn causes unwanted movement (deflection) between the suspension and chassis. Data also shows that temporary changes in spring rates can occur as well. These movements and changes result in unnecessary corrections and inputs from the driver.

FEATURES & BENEFITS
• Replaceable Sub-Assemblies: For the extreme, repetitive track day enthusiast or racer, our high strength steel alloy spherical bearings (with a friction reducing, longevity increasing Teflon liner) outer and inner arm sub-assemblies can be replaced
unlike the motorsports arms, in which case a new set of arms will need to be purchased if the
spherical bearings are worn out.
• Adjustable Suspension Geometry: Adjust dynamic camber values and roll center heights with our
unique zinc plated steel bushings.
• Solid Monoball Control Arm Ends: Offers better handling and a more responsive suspension over the
factory one-piece rubber injected control arm by eliminating bushing deflection (also uses the same
high strength steel alloy spherical bearing found in our control arm monoball kit).
• 6061 Aerospace Grade Billet Aluminum Construction: Allows for a more uniform molecular structure
at every point of the arm over the cast components providing a more durable and inherently
stronger part. Manufacturing from billet aluminum rather than casting results in fewer impurities in
the metal.
• Anodized Aluminum Surfaces and Zinc Plated Steel Parts: Allows for better corrosion resistance
against the elements.

AVAILABLE FOR MOST PORSCHE 996, 986, 981, 982, 987 & 997 MODELS INCLUDING TURBO, GT2, GT2RS, GT3 & GT3RS

RSS TARMAC SERIES Motorsports Suspension Kits have been winning championships and races in various forms of motorsport (Road Racing to Rally) around the world. RSS is the suspension of choice of professional race teams, tuners, track day junkies, and driving enthusiasts around the world.
- 2015 PIRELLI WORLD CHALLENGE TC CHAMPIONS
- 2014 FIA SPANISH RALLY TARMAC CHAMPIONS
- 2013 ROLEX GRAND-AM GX CHAMPIONS
RSS High Performance Tarmac Series Suspension Components are designed, engineered and manufactured on location here in the USA.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

361

您正在查看的产品与这些编号存在交叉引用关系

Front toe steer / bump steer kit XLARGE.



SET OF 2
replacement for 99634713104, 99634713103, 99134713100,

Fits:
FOR ALL Porsche 981, 982, GT4, 991 INCLUDING TURBO & GT3/GT3RS.

Also would fit Porsche 986, 996, 997, 987 that are running extreme amounts of negative camber or that have widened the front track width.

The RSS Adjustable Front Toe/Bump Steer XL Kit is designed for Porsche models that have been lowered. This kit will help minimize the suspension geometry change in the front of the vehicle. Allows for bump steer adjustment. Improves handling, feedback and control.

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

371

您正在查看的产品与这些编号存在交叉引用关系