专业工具

适配器发动机箱支架。

适合:
保时捷 911
保时捷 964
保时捷 993
保时捷 986 / 996
保时捷 987 / 997

该转接环设计用于使用四个 3/8 英寸螺栓将发动机箱体直接安装到任何通用发动机支架上，从而使发动机能够 360 度旋转。

它经过精密加工，具有所有必要的凹槽和槽口，以确保发动机部件（包括飞轮及其相应的锁定工具）有适当的间隙。

博克 (Bock) 发动机工作台支架。

#北环赛道#

适合：
保时捷 356
保时捷 911 912 F/G
保时捷 930
保时捷 914
保时捷 964
保时捷 993
保时捷 996
保时捷 997
保时捷 986/987 Boxster
保时捷 987c Cayman

参考编号：
00072120100, 000.721.201.00, 000 721 201 00, P201

为改装您的保时捷发动机，我们提供发动机支架。法兰表面与悬臂一起连接到安装轴，可确保发动机牢固且同时易于安装到滚动发动机支架上。
在这里，您可以获得所需的支架，以便能够将发动机支架安装在工作台或类似物上。
我们的项目包括适用于所有经典保时捷以及 3.4-3.8L 水冷发动机的发动机支架。
该支架适用于直径为 60 毫米的发动机支架。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

6822

您正在查看的产品与这些编号存在交叉引用关系

996 / 997 GT3 凸轮挡板

#斯托姆斯基#

当 GT3 和 Turbo vario 升程进气凸轮被替换为任何 996/997 Mezger 发动机上的静态正时赛车凸轮时，请使用这些高品质铝制盖替换笨重的工厂式凸轮盖。

直接替换所有 GT3 Cup 和 RSR 引擎以及所有调谐器应用程序。

按一对/套（2）出售。

Crankcase head stud driver for Porsche All 911 964 993 996 / 997 GT3 & Turbo Models 1965-On



Double-nutting a head stud to install it into the engine case not only takes time, but can be stressful for the threads, and can lead to variations in stud depth (unless you are extra careful when removing the double nuts). Protect your hardware investment and speed installation by using STOMSKI RACING's Head Stud Driver.

Made from black oxide finished hardened steel, this uniquely designed tool threads onto the head stud but will not clamp on to the threads, making installation faster, gentler, and more accurate.

Cylinder press for Porsche 996/997 GT3



Here is the ultimate tool to press the cylinders in and out of the water jacket on GT3, Turbo, and RS/RSR 996/997 engines.

This kit includes everything you need to safely, accurately, quickly, and conveniently perform this critical task.

Each kit contains:
• ring compressor (1 @102.7)*,
• Delrin cylinder spacers (4),
• complete stainless steel/AL press,
• aluminum cylinder bushing,
• bolts, and a sturdy storage case.

*100mm ring compressor (1) available separately.

Cylinder press for Porsche 996/997 GT3 with 100mm ring compressor



Here is the ultimate tool to press the cylinders in and out of the water jacket on GT3, Turbo, and RS/RSR 996/997 engines.

This kit includes everything you need to safely, accurately, quickly, and conveniently perform this critical task.

Each kit contains:
• ring compressor (1 @100),
• Delrin cylinder spacers (4),
• complete stainless steel/AL press,
• aluminium cylinder bushing,
• bolts, and a sturdy storage case.

Heat exchanger pressure tester for Porsche 996/997 Turbo/GT2/GT3



Some GT3 engines are experiencing oil-to-coolant intermixing. While there are potentially several sources of intermixing, faulty engine mounted oil-to-coolant heat exchangers are a major source. Now, with STOMSKI RACING's GT3 Heat Exchanger Tester set, you can confirm if your exchanger is faulty and needs replacing, or whether the source of the contamination is elsewhere. This set of CNC machined gauge blocks is machined from 6061 aluminum for years of service and comes complete with all gauges, seals, valves, and hardware.

Also works on the GT2 and 996/997 TT engines as well.

发动机支架用于发动机支架。

#北环赛道#

适合：
保时捷 356
保时捷 911 912 F/G
保时捷 930
保时捷 914
保时捷 964
保时捷 993
保时捷 996 turbo/GT2/GT3
保时捷 997 turbo/GT2/GT3
吸料管外径D=60mm

参考编号：
00072120100, 000.721.201.00, 000 721 201 00, P201

为了改装您的保时捷发动机，我们提供此发动机支架。法兰表面与悬臂一起连接到安装轴，可安全且同时轻松将发动机连接到滚动发动机支架上。或者，您可以使用发动机支架通过轴承座将发动机安装到工作台上。我们的计划中提供带和不带安装支架的所有经典保时捷的发动机支架。

注意：零件的颜色可能与所示颜色不同。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

6898

您正在查看的产品与这些编号存在交叉引用关系

适用于 2009 年至今的 911/997/991/ Boxster 和 Cayman (9A1) 上的保时捷 DFI 发动机的排气螺栓维修套件

#斯托姆斯基#

蝙蝠侠，螺栓断了！即使是水冷发动机上最新一代的 DFI (9A1) 缸盖也报告了排气螺栓断裂的情况。从简单的排气系统更新到发动机拆卸，排气歧管螺栓断裂、生锈和断裂的问题一直困扰着我们。发动机在车上时，很少能准确地拆除断裂的螺栓，即使拆除后，这项任务也很耗时，如果不小心，可能会导致缸盖损坏或维修失误。STOMSKI RACING 针对这些问题的答案是 SR069，这套工具可以轻松、准确、灵活地让您钻出断裂的螺栓 - 发动机仍在车上 - 节省时间和麻烦。CNC 铣削板可以精确地定位断裂的螺栓和/或螺栓孔。使用我们独特设计的翼形螺钉，SR069 板可锁定到位（通过将翼形螺钉拧到断裂的螺栓上或使用提供的螺栓穿过 SR069 翼形螺钉）。使用随附的导向钻和钻孔导向器，可以钻出故障螺栓，形成一个完全垂直且居中的孔，如果需要，可以使用随附的 M8x1.25 丝锥进行钻孔。

套件包括阳极氧化铝固定装置、钻头、带延长杆的丝锥、钻具/导向器、翼形螺钉和五金件，均装在坚固的存储盒中。还包括我们的 SR065D 钻头导向器。

Exhaust bolt repair kit for all Porsche 996/997 GT3s, GT2s, and TTs.



Avoid the headache of trying to drill out broken exhaust bolts on the GT3 engines.

A CNC milled plate indexes precisely off of the broken bolts and/or bolt holes. Using our uniquely designed Thumb Screws, the SR068 plate is locked in place (by threading a Thumb Screw over a broken bolt or by using a supplied bolt threaded through the SR068 Thumb Screw). With the included pilot drills and drill guides, the faulty bolt can be drilled out, producing a perfectly perpendicular and centered hole that if necessary can be chased with the supplied M8x1.25 tap.

Kit includes: aluminum fixture, drill bits, tap with extension, drill jigs/guides, Thumb Screws, and hardware in a sturdy storage case. Now also includes our SR065D drill guide.

适用于保时捷 GT3/GT2 的 GT3 凸轮正时装置 V2。

#斯托姆斯基#

无论您是想提前或延缓凸轮正时、升级凸轮，还是只是想以绝对精度设置任何 GT3/GT2 发动机上的凸轮正时，这都是完成这些任务的最精确的工具。无需满足于使用工厂工具完成的“足够接近”或“大致”设置。
STOMSKI RACING 的 GT3 凸轮正时装置为所有凸轮和设置提供绝对的准确性、无限的可调性和卓越的灵活性。
包括完整的装置，带有 ASME/ANSI 认证的刻度盘指示器和一个（12 毫米或 14 毫米）TDC 指示器，带行程计（SR092 或 SR093）。包括存储箱。

Oil pressure relief plug extractor Porsche 911 / 964 / 993 / 996 / 997



Tolerance between the pressure relief plug and its galley are very close, and the slightest bit of gunk, corrosion, or bur will cause the plug to freeze up in the oil passage. A magnet is rarely powerful enough to overcome the seized plug, and leaving it in place is never an option.
Using STOMSKI RACING's Oil Pressure Relief Plug Extractor makes the task of removing the stuck plug a breeze, and allows you to ensure clean oil passages, and a properly operating bypass system.

The collet-based tool slides easily into the open end of the seized plug and a simple turn or two of the internal socket head cap screw expands the tool, grasping the plug to ensure easy removal.

Anodized Aluminum.

Time-Sert™ thread repair kit for SR065/SR067/SR068 for Porsche 911 / Boxster / 996 / 997



For exhaust port studs on 911, Boxster, 996/997 or GT3 heads where the threads have been pulled, or to recover from an already improper repair, we have developed this Time-Sert(tm) kit so you may use our SR065, SR067, SR068 or SR069 tools to insert a Time-Sert and save an otherwise ruined head. In addition to the standard Time-Sert(tm) parts (short P drill, counter-bore, tap, insert tool, and 5 short inserts), our kit also includes a full length P drill, two drill jigs/bushings to guide the P drill and tap in our SR065, SR067, or SR068 fixtures, 5 full length inserts, and 5 studs.

Time-Sert(tm) is a registered trademark of TIME FASTENER COMPANY