专业工具

适配器发动机箱支架。

适合:
保时捷 911
保时捷 964
保时捷 993
保时捷 986 / 996
保时捷 987 / 997

该转接环设计用于使用四个 3/8 英寸螺栓将发动机箱体直接安装到任何通用发动机支架上，从而使发动机能够 360 度旋转。

它经过精密加工，具有所有必要的凹槽和槽口，以确保发动机部件（包括飞轮及其相应的锁定工具）有适当的间隙。

保时捷 994 / 963 / 996 GT3 / 997 GT3 辅助链条张紧器

#斯托姆斯基#

STOMSKI RACING 全新推出的这款工具紧凑型版本，安装和拆卸更加便捷——只需使用随附的翼形螺钉即可安装这些张紧器，无需任何工具。精准的弹簧和公差确保链条张力适中。

不锈钢和阳极氧化铝确保该工具能够使用多年。

一套两个。

博克 (Bock) 发动机工作台支架。

#北环赛道#

适合：
保时捷 356
保时捷 911 912 F/G
保时捷 930
保时捷 914
保时捷 964
保时捷 993
保时捷 996
保时捷 997
保时捷 986/987 Boxster
保时捷 987c Cayman

参考编号：
00072120100, 000.721.201.00, 000 721 201 00, P201

为改装您的保时捷发动机，我们提供发动机支架。法兰表面与悬臂一起连接到安装轴，可确保发动机牢固且同时易于安装到滚动发动机支架上。
在这里，您可以获得所需的支架，以便能够将发动机支架安装在工作台或类似物上。
我们的项目包括适用于所有经典保时捷以及 3.4-3.8L 水冷发动机的发动机支架。
该支架适用于直径为 60 毫米的发动机支架。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

6822

您正在查看的产品与这些编号存在交叉引用关系

996 / 997 GT3 凸轮挡板

#斯托姆斯基#

当 GT3 和 Turbo vario 升程进气凸轮被替换为任何 996/997 Mezger 发动机上的静态正时赛车凸轮时，请使用这些高品质铝制盖替换笨重的工厂式凸轮盖。

直接替换所有 GT3 Cup 和 RSR 引擎以及所有调谐器应用程序。

按一对/套（2）出售。

Cam profile plates for Porsche 996 / 997 GT3



Use our GT3 Cam Profile Plates to rough-in your GT3 cams prior to timing.
CNC machined from high quality aluminum and hard-coat anodized for protection and good looks, these plates will speed up setup time and ensure your cams are properly positioned before you start timing the engine.
With four cams and 24 valves to coordinate, these plates are sure to add that bit of confidence before you turn the engine over for the first time.

Sold as a set of two plates.

Cam sprocket tool for Porsche 996 / 997 GT3



STOMSKI RACING's version of this tool works on both the intake and the exhaust cams on the Cup engines and on all non-vario cams for the other GT3-type engines. This tool replaces the factory tool P9653/1. Moreover, additional refinements of this tool ensures that while torquing either the 16mm hex or the triple-box cam sprocket bolts, your tool is securely bushed and supported in the center of the tool, and thus will not slip off or round off the bolts. Black oxide finished hardened steel.

Crankcase head stud driver for Porsche All 911 964 993 996 / 997 GT3 & Turbo Models 1965-On



Double-nutting a head stud to install it into the engine case not only takes time, but can be stressful for the threads, and can lead to variations in stud depth (unless you are extra careful when removing the double nuts). Protect your hardware investment and speed installation by using STOMSKI RACING's Head Stud Driver.

Made from black oxide finished hardened steel, this uniquely designed tool threads onto the head stud but will not clamp on to the threads, making installation faster, gentler, and more accurate.

Cylinder press for Porsche 996/997 GT3



Here is the ultimate tool to press the cylinders in and out of the water jacket on GT3, Turbo, and RS/RSR 996/997 engines.

This kit includes everything you need to safely, accurately, quickly, and conveniently perform this critical task.

Each kit contains:
• ring compressor (1 @102.7)*,
• Delrin cylinder spacers (4),
• complete stainless steel/AL press,
• aluminum cylinder bushing,
• bolts, and a sturdy storage case.

*100mm ring compressor (1) available separately.

Cylinder press for Porsche 996/997 GT3 with 100mm ring compressor



Here is the ultimate tool to press the cylinders in and out of the water jacket on GT3, Turbo, and RS/RSR 996/997 engines.

This kit includes everything you need to safely, accurately, quickly, and conveniently perform this critical task.

Each kit contains:
• ring compressor (1 @100),
• Delrin cylinder spacers (4),
• complete stainless steel/AL press,
• aluminium cylinder bushing,
• bolts, and a sturdy storage case.

DigiDix™ Digital degree wheel cam timing system for Porsche all 911 and GT3 engines



A revolution in cam timing, STOMSKI RACING's DigiDix™ - Digital Degree Wheel - provides the most accurate, easy to use degree wheel ever. No more awkward setups, questionable readings, convoluted pointers, or imprecise measurements. With DigiDix™, simply bolt the sensor/adapter to the flywheel-end of the crankshaft and secure the torsion arm. Setup time is less than one minute. You are now ready to measure crank rotation to one tenth (.1) of one degree accuracy and repeatability.

DigiDix™ includes a 3 foot cable for easy reading anywhere on the engine and fits all 911 and GT3 engines (and others by special order). Storage case included.

STOMSKI RACING - "reinventing the wheel."

Stomski Racing SR124 Engine case splitter for Porsche 911



No more hammering, chiseling, swearing, heating, prying or praying to get an 911 engine case apart. STOMSKI RACING'S SR124 ELEGANTLY and GENTLY separates the engine case halves and not only shortens the process of engine tear-down, but it also protects what doubtlessly is an expensive asset- the engine case itself. The rare #s matching early 911S sand-cast aluminum case, or the impossible to find 911 GT3 RSR case, or the early magnesium case that seems so fragile, all can NOW be protected from the threat of the block of wood and lead hammer, or the torch, or the pry-bar and chisel.
SR124 includes a CNC precision machined aluminum platform that you bolt to four head studs (ideally over #2 or #5) using the included thumbscrews. An over-sized drive-screw (stainless steel) is then threaded through the platform to mate with a high-load bearing in our specially designed rod cap that presses against the wrist pin of #2 or #5 connecting rod that is at bottom-dead-center. As you slowly use a wrench or ratchet to tighten the drive-screw, the torque of the SR124 splitter is evenly distributed through the entire crankshaft, pressing against ALL 8 main bearings. Once the slack is taken up, only GENTLE effort on the drive screw is required to split even the most belligerent of cases.
The SR124 platform is designed to work on all Mezger 911s (2.0 through 997) and includes Delrin inserts/sleeves that protect the head studs from scratches or dings.

Heat exchanger pressure tester for Porsche 996/997 Turbo/GT2/GT3



Some GT3 engines are experiencing oil-to-coolant intermixing. While there are potentially several sources of intermixing, faulty engine mounted oil-to-coolant heat exchangers are a major source. Now, with STOMSKI RACING's GT3 Heat Exchanger Tester set, you can confirm if your exchanger is faulty and needs replacing, or whether the source of the contamination is elsewhere. This set of CNC machined gauge blocks is machined from 6061 aluminum for years of service and comes complete with all gauges, seals, valves, and hardware.

Also works on the GT2 and 996/997 TT engines as well.

发动机支架用于发动机支架。

#北环赛道#

适合：
保时捷 356
保时捷 911 912 F/G
保时捷 930
保时捷 914
保时捷 964
保时捷 993
保时捷 996 turbo/GT2/GT3
保时捷 997 turbo/GT2/GT3
吸料管外径D=60mm

参考编号：
00072120100, 000.721.201.00, 000 721 201 00, P201

为了改装您的保时捷发动机，我们提供此发动机支架。法兰表面与悬臂一起连接到安装轴，可安全且同时轻松将发动机连接到滚动发动机支架上。或者，您可以使用发动机支架通过轴承座将发动机安装到工作台上。我们的计划中提供带和不带安装支架的所有经典保时捷的发动机支架。

注意：零件的颜色可能与所示颜色不同。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

6898

您正在查看的产品与这些编号存在交叉引用关系

Exhaust bolt repair kit for all Porsche 996/997 GT3s, GT2s, and TTs.



Avoid the headache of trying to drill out broken exhaust bolts on the GT3 engines.

A CNC milled plate indexes precisely off of the broken bolts and/or bolt holes. Using our uniquely designed Thumb Screws, the SR068 plate is locked in place (by threading a Thumb Screw over a broken bolt or by using a supplied bolt threaded through the SR068 Thumb Screw). With the included pilot drills and drill guides, the faulty bolt can be drilled out, producing a perfectly perpendicular and centered hole that if necessary can be chased with the supplied M8x1.25 tap.

Kit includes: aluminum fixture, drill bits, tap with extension, drill jigs/guides, Thumb Screws, and hardware in a sturdy storage case. Now also includes our SR065D drill guide.