专业工具

适配器发动机箱支架。

适合:
保时捷 911
保时捷 964
保时捷 993
保时捷 986 / 996
保时捷 987 / 997

该转接环设计用于使用四个 3/8 英寸螺栓将发动机箱体直接安装到任何通用发动机支架上，从而使发动机能够 360 度旋转。

它经过精密加工，具有所有必要的凹槽和槽口，以确保发动机部件（包括飞轮及其相应的锁定工具）有适当的间隙。

保时捷 994 / 963 / 996 GT3 / 997 GT3 辅助链条张紧器

#斯托姆斯基#

STOMSKI RACING 全新推出的这款工具紧凑型版本，安装和拆卸更加便捷——只需使用随附的翼形螺钉即可安装这些张紧器，无需任何工具。精准的弹簧和公差确保链条张力适中。

不锈钢和阳极氧化铝确保该工具能够使用多年。

一套两个。

博克 (Bock) 发动机工作台支架。

#北环赛道#

适合：
保时捷 356
保时捷 911 912 F/G
保时捷 930
保时捷 914
保时捷 964
保时捷 993
保时捷 996
保时捷 997
保时捷 986/987 Boxster
保时捷 987c Cayman

参考编号：
00072120100, 000.721.201.00, 000 721 201 00, P201

为改装您的保时捷发动机，我们提供发动机支架。法兰表面与悬臂一起连接到安装轴，可确保发动机牢固且同时易于安装到滚动发动机支架上。
在这里，您可以获得所需的支架，以便能够将发动机支架安装在工作台或类似物上。
我们的项目包括适用于所有经典保时捷以及 3.4-3.8L 水冷发动机的发动机支架。
该支架适用于直径为 60 毫米的发动机支架。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

6822

您正在查看的产品与这些编号存在交叉引用关系

凸轮/动力转向阻断板适用于保时捷 911 / 964 / 993

#斯托姆斯基#

使用此板封闭 993 的凸轮塔上的动力转向泵开口，或封闭涡轮增压器和早期 911 的凸轮塔上的油泵和喷射泵开口。此板是定制设计的，适用于库存和非库存凸轮。

阳极氧化铝。

适用于 1998 年之前的 911。

单独出售。

Cam timing indicator fixture (dual) for Porsche 911 / 964 / 993



STOMSKI RACING finally takes the guess work out of timing the 911 engines. No longer do you need to hassle with convoluted setups, indicator contacts slipping off of the valve retainer, or measurements that will not repeat. This fixture indexes off of two cam carrier studs and literally takes only 10 seconds to setup. Once in place, the SR098 consistently and repeatedly holds the dial indicator contact in the same place on the valve retainer- EVERY time.

Includes adapters and extensions for both metric and AGD (inch) indicators.
Anodized aluminum for years of service.

For all 911s including the 993.

Please note: Gauges sold separately.

Cam sprocket bolt tool for Porsche 993



STOMSKI RACING's version of the factory P9582 tool combines the basics of the factory tool and improves on it by adding an integral 19mm bushed socket that prevents slippage and rounding off of the cam bolt on the end of the 993 cam shafts. The cam bolt on the 993s requires a torque of 88 foot pounds. Tightening the bolt to this spec, or loosening it using a breaker bar and the factory long-armed cam tool requires dexterity, leverage, and serious luck that the deep socket does not slip off the head of the bolt, rounding it over, or busting knuckles in the process.

STOMSKI RACING's SR9582 securely holds an impact-quality socket in the center of a precision machined hardened steel socket, ensuring ease and accuracy in loosening the bolt, or setting the required torque. The bushing prevents the socket from being leveraged off the bolt head, keeping it squarely in place for the most accurate torque and security during installation and removal.

Crankcase head stud driver for Porsche All 911 964 993 996 / 997 GT3 & Turbo Models 1965-On



Double-nutting a head stud to install it into the engine case not only takes time, but can be stressful for the threads, and can lead to variations in stud depth (unless you are extra careful when removing the double nuts). Protect your hardware investment and speed installation by using STOMSKI RACING's Head Stud Driver.

Made from black oxide finished hardened steel, this uniquely designed tool threads onto the head stud but will not clamp on to the threads, making installation faster, gentler, and more accurate.

DigiDix™ Digital degree wheel cam timing system for Porsche all 911 and GT3 engines



A revolution in cam timing, STOMSKI RACING's DigiDix™ - Digital Degree Wheel - provides the most accurate, easy to use degree wheel ever. No more awkward setups, questionable readings, convoluted pointers, or imprecise measurements. With DigiDix™, simply bolt the sensor/adapter to the flywheel-end of the crankshaft and secure the torsion arm. Setup time is less than one minute. You are now ready to measure crank rotation to one tenth (.1) of one degree accuracy and repeatability.

DigiDix™ includes a 3 foot cable for easy reading anywhere on the engine and fits all 911 and GT3 engines (and others by special order). Storage case included.

STOMSKI RACING - "reinventing the wheel."

Stomski Racing SR124 Engine case splitter for Porsche 911



No more hammering, chiseling, swearing, heating, prying or praying to get an 911 engine case apart. STOMSKI RACING'S SR124 ELEGANTLY and GENTLY separates the engine case halves and not only shortens the process of engine tear-down, but it also protects what doubtlessly is an expensive asset- the engine case itself. The rare #s matching early 911S sand-cast aluminum case, or the impossible to find 911 GT3 RSR case, or the early magnesium case that seems so fragile, all can NOW be protected from the threat of the block of wood and lead hammer, or the torch, or the pry-bar and chisel.
SR124 includes a CNC precision machined aluminum platform that you bolt to four head studs (ideally over #2 or #5) using the included thumbscrews. An over-sized drive-screw (stainless steel) is then threaded through the platform to mate with a high-load bearing in our specially designed rod cap that presses against the wrist pin of #2 or #5 connecting rod that is at bottom-dead-center. As you slowly use a wrench or ratchet to tighten the drive-screw, the torque of the SR124 splitter is evenly distributed through the entire crankshaft, pressing against ALL 8 main bearings. Once the slack is taken up, only GENTLE effort on the drive screw is required to split even the most belligerent of cases.
The SR124 platform is designed to work on all Mezger 911s (2.0 through 997) and includes Delrin inserts/sleeves that protect the head studs from scratches or dings.

Head stud height setter for Porsche 911



Precisely set the height of head studs on all the 911 engines using this innovative tool. The Delrin insert protects the engine case from scratches or marring, while the adjustable three-piece anodized aluminium tubular construction provides complete flexibility for all engine setups, tools, and stud combinations.

For all 911s including GT3s.

发动机支架用于发动机支架。

#北环赛道#

适合：
保时捷 356
保时捷 911 912 F/G
保时捷 930
保时捷 914
保时捷 964
保时捷 993
保时捷 996 turbo/GT2/GT3
保时捷 997 turbo/GT2/GT3
吸料管外径D=60mm

参考编号：
00072120100, 000.721.201.00, 000 721 201 00, P201

为了改装您的保时捷发动机，我们提供此发动机支架。法兰表面与悬臂一起连接到安装轴，可安全且同时轻松将发动机连接到滚动发动机支架上。或者，您可以使用发动机支架通过轴承座将发动机安装到工作台上。我们的计划中提供带和不带安装支架的所有经典保时捷的发动机支架。

注意：零件的颜色可能与所示颜色不同。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

6898

您正在查看的产品与这些编号存在交叉引用关系

Exhaust head stud repair kit for Porsche Air-cooled 911's



Never lose sleep again over a bent or broken exhaust stud on a 911 engine. This new tool is a must for every 911 mechanic and will pay for itself the first time you use it. This is a quick and totally accurate tool to repair and replace broken studs without damaging the head, or worse, having to remove the engine. The SR065 fixture indexes off of the exhaust port (by using one of the various sized port bushings included), secures to the opposite stud, and allows you to drill out, tap, and replace the stud dead on, every time. Includes LH drill bits, tap with extension, drill jigs/guides, port bushings, and a sturdy storage case.

Now includes our SR065D drill guide.

Fits ALL of the 911 heads including the 993.

插孔

#北环赛道#

适合：
自 1985 年 8 月起的保时捷 944
保时捷 964
保时捷 968
保时捷 993
保时捷 996 Carrera 2/4 / 996 Turbo
保时捷 997 Carrera 2/4 / 997 Turbo
保时捷 986 Boxster
保时捷 987 Boxster
保时捷 987C Cayman


如果您想在通常的千斤顶位置举升车辆，就不能绕过适配器。只有这样，车辆才能安全稳定地升起，不会有滑落的风险，并且车身底部保护/油漆也受到保护。由于原装支架中的销钉几何形状，该适配器可以旋转，并牢固地固定在车辆上。

优点：
• 采用 7000 铝合金，强度高
• 防止刮伤底盘保护装置/油漆
• 可使用通用千斤顶进行安全顶升
• 锥形轴颈底座具有锁定功能
• 几何形状适合于所提及的保时捷车型。

相关参考编号
相关编号、被取代编号、交叉引用编号或替代编号，供比较之用。

1154

您正在查看的产品与这些编号存在交叉引用关系