Control Arms Rear

Sold as a pair this includes 2 bolts, 2 lock nuts, 4 washers and 4 eccentric locks.

993 - Can be used on upper control arms, and lower toe arms.
996/997/986/987 - Can be used on lower control arms and lower toe arms.

With no replacement bushes available from Porsche, these uprated Powerflex bushes provide a high-performance, durable, and cost-effective alternative to purchasing a complete arm. 

Fits:
Porsche 993 Carrera 1994-98
Porsche 993 Carrera RS 1995-96
Porsche 993 Turbo 1995-98
Porsche 993 GT2 1996-98

Powerflex diagram ref. 13.

Sold as a set of two, these bushes are a direct replacement for the inner bush on part number 99333104301 - the rearmost control arm on the rear axle, which manages toe angle adjustment.

The Powerflex Range:

Road Series (Road & Fast Road) - POWERFLEX Road Series bushes improve your cars’ road holding and chassis performance by controlling the amount of unwanted flex in the suspension. This means the suspension is doing what it is supposed to. It means your tyres have greater contact with the road at all times, therefore, improving safety and performance. Correctly formulated polyurethane is as good if not better at noise, vibration and harshness suppression when compared to worn rubber. Our Road bushes offer Prolonged tyre life, Improved performance, Increase safety, and Greater cost-effectiveness.

Black Series (Track & Motorsport) - POWERFLEX Black Series bushes are manufactured using our Black 95 Shore A compound to provide maximum control of chassis geometry. They are designed for the Track, ready to Race and are engineered to be the best. This compound can be up to 80% more resistant to load than standard rubber and 25% stiffer than our purple performance material. If your requirements are purely for the ultimate in handling and chassis performance then Powerflex Black Series are unique, offering the most precise and accurate alignment for your chassis.

Heritage Collection (Classic & Restoration Use) - POWERFLEX Heritage Collection bushes are manufactured using modern-day materials with properties biased for the road. These dark grey coloured bushes will improve any collector’s car, whilst retaining the same standard appearance of a rubber bush. Our new range speaks to the growing demand for quality replacement parts that have an aesthetic in keeping with’ the look of the original part and restoration project as a whole whilst carrying all of the performance and longevity benefits offered by Powerflex’s unique blend of polyurethane. Going a step further than simply using the same material and durometer of hardness for all of our parts, each part location has its own shore designation to ensure improved suspension performance without discomfort or vibration, all of which ship in our new ‘Classic’ Dark Grey colour suitable for all road-based applications.

Powerflex Materials:

The materials used by Powerflex are colour coded to make them easily identifiable. Below explains the shore rating and their common uses.

Red 65A – Used for our Universal exhaust mounts and diesel engine mounts.
Yellow 70A – Mainly used for engine mounts, diff mounts and subframe mounts or areas where the bush needs a lot of movement and absorption.
Purple 80A – Our most common material. This is used in most areas of the suspension and provides the right mix between performance and compliance.
Black 95A – Our hardest material. This is used mostly for our Black Series range or in our Road Series where the vehicle’s standard suspension demands require us to use this hardness of material i.e. in areas of high load.

Grey* - Used specifically for our Heritage Collection. This can be any of the durometers mentioned but will always be the same as the equivalent part from our Road Series i.e. if it’s Purple 80A in our Road Series, it’d be Grey 80A in our Heritage Collection. On our Road Series and Heritage Collection kits, we can use a mix of all 4 of our materials. During the development stages, we test the original bush and see what the requirements are for strength and movement. At that point, we then decide which of our materials would be best suited. We don’t believe in a one material suits all rule. Manufacturers will do the same and will use different shore rubbers, however, it’s not as noticeable as all rubber bushes look visually similar.

With no replacement bushes available from Porsche, these uprated Powerflex bushes provide a high-performance, durable, and cost-effective alternative to purchasing a complete arm. 

Fits:
Porsche 993 Carrera 1994-98
Porsche 993 Carrera RS 1995-96
Porsche 993 Turbo 1995-98
Porsche 993 GT2 1996-98

Powerflex diagram ref. 13.

Sold as a set of two, these bushes are a direct replacement for the inner bush on part number 99333104301 - the rearmost control arm on the rear axle, which manages toe angle adjustment.

The Powerflex Range:

Road Series (Road & Fast Road) - POWERFLEX Road Series bushes improve your cars’ road holding and chassis performance by controlling the amount of unwanted flex in the suspension. This means the suspension is doing what it is supposed to. It means your tyres have greater contact with the road at all times, therefore, improving safety and performance. Correctly formulated polyurethane is as good if not better at noise, vibration and harshness suppression when compared to worn rubber. Our Road bushes offer Prolonged tyre life, Improved performance, Increase safety, and Greater cost-effectiveness.

Black Series (Track & Motorsport) - POWERFLEX Black Series bushes are manufactured using our Black 95 Shore A compound to provide maximum control of chassis geometry. They are designed for the Track, ready to Race and are engineered to be the best. This compound can be up to 80% more resistant to load than standard rubber and 25% stiffer than our purple performance material. If your requirements are purely for the ultimate in handling and chassis performance then Powerflex Black Series are unique, offering the most precise and accurate alignment for your chassis.

Heritage Collection (Classic & Restoration Use) - POWERFLEX Heritage Collection bushes are manufactured using modern-day materials with properties biased for the road. These dark grey coloured bushes will improve any collector’s car, whilst retaining the same standard appearance of a rubber bush. Our new range speaks to the growing demand for quality replacement parts that have an aesthetic in keeping with’ the look of the original part and restoration project as a whole whilst carrying all of the performance and longevity benefits offered by Powerflex’s unique blend of polyurethane. Going a step further than simply using the same material and durometer of hardness for all of our parts, each part location has its own shore designation to ensure improved suspension performance without discomfort or vibration, all of which ship in our new ‘Classic’ Dark Grey colour suitable for all road-based applications.

Powerflex Materials:

The materials used by Powerflex are colour coded to make them easily identifiable. Below explains the shore rating and their common uses.

Red 65A – Used for our Universal exhaust mounts and diesel engine mounts.
Yellow 70A – Mainly used for engine mounts, diff mounts and subframe mounts or areas where the bush needs a lot of movement and absorption.
Purple 80A – Our most common material. This is used in most areas of the suspension and provides the right mix between performance and compliance.
Black 95A – Our hardest material. This is used mostly for our Black Series range or in our Road Series where the vehicle’s standard suspension demands require us to use this hardness of material i.e. in areas of high load.

Grey* - Used specifically for our Heritage Collection. This can be any of the durometers mentioned but will always be the same as the equivalent part from our Road Series i.e. if it’s Purple 80A in our Road Series, it’d be Grey 80A in our Heritage Collection. On our Road Series and Heritage Collection kits, we can use a mix of all 4 of our materials. During the development stages, we test the original bush and see what the requirements are for strength and movement. At that point, we then decide which of our materials would be best suited. We don’t believe in a one material suits all rule. Manufacturers will do the same and will use different shore rubbers, however, it’s not as noticeable as all rubber bushes look visually similar.

With no replacement bushes available from Porsche, these uprated Powerflex bushes provide a high-performance, durable, and cost-effective alternative to purchasing a complete arm. 

Fits:
Porsche 993 Carrera 1994-98
Porsche 993 Carrera RS 1995-96
Porsche 993 Turbo 1995-98
Porsche 993 GT2 1996-98

Powerflex diagram ref. 13.

Sold as a set of two, these bushes are a direct replacement for the inner bush on part number 99333104301 - the rearmost control arm on the rear axle, which manages toe angle adjustment.

The Powerflex Range:

Road Series (Road & Fast Road) - POWERFLEX Road Series bushes improve your cars’ road holding and chassis performance by controlling the amount of unwanted flex in the suspension. This means the suspension is doing what it is supposed to. It means your tyres have greater contact with the road at all times, therefore, improving safety and performance. Correctly formulated polyurethane is as good if not better at noise, vibration and harshness suppression when compared to worn rubber. Our Road bushes offer Prolonged tyre life, Improved performance, Increase safety, and Greater cost-effectiveness.

Black Series (Track & Motorsport) - POWERFLEX Black Series bushes are manufactured using our Black 95 Shore A compound to provide maximum control of chassis geometry. They are designed for the Track, ready to Race and are engineered to be the best. This compound can be up to 80% more resistant to load than standard rubber and 25% stiffer than our purple performance material. If your requirements are purely for the ultimate in handling and chassis performance then Powerflex Black Series are unique, offering the most precise and accurate alignment for your chassis.

Heritage Collection (Classic & Restoration Use) - POWERFLEX Heritage Collection bushes are manufactured using modern-day materials with properties biased for the road. These dark grey coloured bushes will improve any collector’s car, whilst retaining the same standard appearance of a rubber bush. Our new range speaks to the growing demand for quality replacement parts that have an aesthetic in keeping with’ the look of the original part and restoration project as a whole whilst carrying all of the performance and longevity benefits offered by Powerflex’s unique blend of polyurethane. Going a step further than simply using the same material and durometer of hardness for all of our parts, each part location has its own shore designation to ensure improved suspension performance without discomfort or vibration, all of which ship in our new ‘Classic’ Dark Grey colour suitable for all road-based applications.

Powerflex Materials:

The materials used by Powerflex are colour coded to make them easily identifiable. Below explains the shore rating and their common uses.

Red 65A – Used for our Universal exhaust mounts and diesel engine mounts.
Yellow 70A – Mainly used for engine mounts, diff mounts and subframe mounts or areas where the bush needs a lot of movement and absorption.
Purple 80A – Our most common material. This is used in most areas of the suspension and provides the right mix between performance and compliance.
Black 95A – Our hardest material. This is used mostly for our Black Series range or in our Road Series where the vehicle’s standard suspension demands require us to use this hardness of material i.e. in areas of high load.

Grey* - Used specifically for our Heritage Collection. This can be any of the durometers mentioned but will always be the same as the equivalent part from our Road Series i.e. if it’s Purple 80A in our Road Series, it’d be Grey 80A in our Heritage Collection. On our Road Series and Heritage Collection kits, we can use a mix of all 4 of our materials. During the development stages, we test the original bush and see what the requirements are for strength and movement. At that point, we then decide which of our materials would be best suited. We don’t believe in a one material suits all rule. Manufacturers will do the same and will use different shore rubbers, however, it’s not as noticeable as all rubber bushes look visually similar.

POWERFLEX Black Series bushes are manufactured using our Black 95 Shore A compound to provide maximum control of chassis geometry. They are designed for the Track, ready to Race and are engineered to be the best.

Replacing your car rubber suspension bushes with Polyurethane Suspension Bushes will give you:

- Better road holding
- Constant steering geometry
- Increased tyre life
- More responsive steering
- Longer service life of suspension components

POWERFLEX Black Series bushes are manufactured using our Black 95 Shore A compound to provide maximum control of chassis geometry. 
They are designed for the Track, ready to Race and are engineered to be the best.

Replacing your car rubber suspension bushes with Polyurethane Suspension Bushes will give you:

- Better road holding
- Constant steering geometry
- Increased tyre life
- More responsive steering
- Longer service life of suspension components

POWERFLEX Black Series bushes are manufactured using our Black 95 Shore A compound to provide maximum control of chassis geometry. 
They are designed for the Track, ready to Race and are engineered to be the best.