Side Sill Panels

Front end cap for wide deco sill / rocker.

Fits:
Porsche 911 1969-73 (LWB)
Long Wheel Base Cars

Diagram ref no 28

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90155911

The product you are viewing cross references to these numbers

Heater tube in inner rocker.
Fits left and right

Fits:
Porsche 911 - 1965 to 1969
Porsche 912 - 1965 to 1969

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90157202121

The product you are viewing cross references to these numbers

Heater tube in inner rocker.
Fits left and right



Fits:
Porsche 911 2.0 01/63-07/67
Porsche 912 1.6 01/65-07/67

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90157202121

The product you are viewing cross references to these numbers

Heating tube inside side sill left or right.

This is a bespoke restoration product, you can not buy this from Porsche !

Fits:
Porsche 911/912 1965-68 SWB cars

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91150340000

The product you are viewing cross references to these numbers

Heating tube inside sill (left/right).
This Heater Tube Inside Sill is a Genuine Porsche OE component designed to route heated air through the inner sill section of classic air-cooled Porsche 911 models from 1969 to 1989. The heater tube carries warm air produced by the engine’s heat exchangers through the sill cavity toward the cabin ventilation system.

Fits:
Porsche 911 1969 - 1989

Diagram ref no 15

Function: Installed inside the vehicle’s sill structure, the tube forms a critical part of the classic 911 heating system. It channels heated air forward into the cabin ducting, supporting effective interior heating, windscreen demisting, and overall comfort in cooler conditions.

Over time, original heater tubes can degrade due to heat cycles, age, and corrosion, resulting in reduced airflow or heat loss before reaching the cabin. In severe cases, damaged ducting may allow unwanted fumes or debris into the heating system. Replacing the tube with a Genuine Porsche part restores factory heating efficiency, preserves originality, and ensures long-term reliability of the heating system.

Replace this heater tube if you notice:
• Weak or uneven heater output
•  Cracked, brittle, or collapsed ducting
•  Heat loss before air reaches the cabin
•  Unpleasant odours from the heating system
•  During restoration or refurbishment of the sill or heating system

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91157202502

The product you are viewing cross references to these numbers

Heating tube inside sill, Ø55 mm, length 685 mm.
This heating tube inside sill is a high-quality replacement air-duct tube designed to channel warm air from the exhaust-heated heating system through the sill area of classic Porsche 911 models built from 1969 through 1989 and 356 B/C models. It matches the original part’s fit and performance to maintain proper heating airflow in your vehicle’s cabin.

Fits:
Porsche 356 B/C 1.6 01/1959 - 12/1965
Porsche 911 2.0-3.3 08/1968 - 07/1989
Porsche 912 1.6 01/1965 - 02/1970
Porsche 914 1.7-2.0 01/1969 - 07/1974

Diagram ref no 15

The heating tube directs hot air generated by the engine’s exhaust-heated heat exchangers into the cabin area via the sill ducting. This ensures your classic Porsche’s heater system distributes warmth effectively, improving defogging, defrosting, and passenger comfort in cooler weather.

Function: Installed along the inner sill section, this tube captures heat from the heater system and delivers it through the duct network into the footwell or cabin air distribution points. A properly functioning heater tube helps maintain consistent cabin temperature and prevents heat loss due to damage or age-related degradation of the original ducting.

Over decades of use, original heater tubes can become cracked, brittle, or collapsed, leading to poor airflow, heat loss, or even exhaust gas intrusion into the cabin air system. Replacing the deteriorated tube with an OE Match unit restores effective hot-air distribution, improves cabin comfort and heater efficiency, and keeps the vintage heating system functioning as intended.

Replace this heating tube when you notice:
•  Weak or inconsistent warm air delivery from the heater
•  Deteriorated, cracked, or collapsed heater tubing
•  Excessive heat loss before reaching the cabin
•  Unusual smells from heater ducts (possible leaks)
•  During full heater system or sill restoration work

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91157202502

The product you are viewing cross references to these numbers

Inner rocker panel, thickness 0.8 mm.



Fits:
Porsche 911 2.0L 01/1963-07/1968

Click 'Zoom in' for large parts diagram.
Diagram ref no 19

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90150112

The product you are viewing cross references to these numbers

Jack receiver bracket. 



Fits:
Porsche 911 1966-89

Click 'Zoom in' for large parts diagram.
Diagram ref no 9.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90150115122GRV

The product you are viewing cross references to these numbers

Jack receiver socket. 



Fits:
Porsche 911 1966-73

Click 'Zoom in' for large parts diagram.
Diagram ref no 10.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90150115321GRV

The product you are viewing cross references to these numbers

Jack receiver socket.



Fits:
Porsche 911 1974-89

Click 'Zoom in' for large parts diagram.
Diagram ref no 10.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91150119500

The product you are viewing cross references to these numbers

Jack receiver socket. Porsche 911 1974-89



Fits:
Porsche 911 1974-89

Click 'Zoom in' for large parts diagram.
Diagram ref no 10.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91150119500

The product you are viewing cross references to these numbers

Jacking point plug.



Fits:
Porsche 911 1974-89
Porsche 930 3.0L, 3.3L 1975-89

Click 'Zoom in' for large parts diagram.
Diagram ref no 17.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91155914901

The product you are viewing cross references to these numbers

Jacking point plug.



Fits:
Porsche 911 1974-89
Porsche 930 3.0L, 3.3L 1975-89

Click 'Zoom in' for large parts diagram.
Diagram ref no 17.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91155914901

The product you are viewing cross references to these numbers

Oil Pipe inner support bracket for Door Sill Inner Panel. Porsche 911 1966-89, Weld on oil pipe support bracket
6 Required Per car



Fits:
Porsche 911 1966-89

Click 'Zoom in' for large parts diagram.
Diagram ref no 38

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91150112500GRV

The product you are viewing cross references to these numbers

Rear end cap for wide deco sill / rocker



Fits:
Porsche 911 1969-73 (LWB)
Long Wheel Base Cars

Click 'Zoom in' for large parts diagram.
Diagram ref no 29.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90155911

The product you are viewing cross references to these numbers

Rear torsion bar cover with gasket, bracket and nut. 

Sold individually; x2 required per vehicle. 

Fits:
Porsche 911 1965-86
Porsche 911 (930) Turbo 1975-86

Porsche 912 1966-69
Porsche 912E 1976

Diagram ref. 33.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90150407900

The product you are viewing cross references to these numbers