Original Porsche Part Genuine Porsche part 99911333140

Code: 99911333140

Genuine Porsche part

Original Porsche Part

Additional information:

• This part is brand new and unused.
• Please verify that it is 100% suitable for your specific vehicle before purchase to ensure compatibility.

Before purchasing thoroughly check part to confirm compatibility.

Related products

3 3 3

Manual transmission main shaft seal. Porsche 911 / 964 / 993 / 996 / 997

99911332641/1

Product Information

Manual transmission main shaft seal. 26.5 x 40 mm.
Its function is to act as a primary seal to retain oil around the input (main) shaft of a manual transmission, preventing fluid leaks and protecting driveline components.

Fits:
Porsche 911 Carrera / Turbo 1987 - 1989
Porsche 964 Carrera / Turbo 1989 - 1994
Porsche 993 Carrera / Turbo 1995 - 1998
Porsche 996 Turbo / GT2 / GT3 2001 - 2005
Porsche 997.1 Turbo / GT2 2007 - 2009
Porsche 997.2 Turbo / GT2 2010 - 2013
Porsche 996 GT3 1999 - 2005
Porsche 997 GT3 2007 - 2011

Diagram ref no 12

Application:
• Manual transmission input shaft oil seal
• Cross-referenced with superseded part number: 99911332640

The input shaft seal sits around the input/main shaft where it enters the transmission case. Its job is to keep transmission fluid from leaking out and to prevent contamination from entering the gearbox. By maintaining a secure seal around the rotating shaft, this component helps preserve optimal lubrication, reduce wear, and support smooth gear operation.

In a manual transmission, the input shaft takes power from the clutch and delivers it into the gearbox. The seal must endure rotation, pressure changes, heat, and exposure to transmission fluid, forming a durable barrier that keeps oil inside while preventing dirt and debris from entering. A properly functioning input shaft seal is crucial for transmission longevity and performance.

Over time and mileage, seals can harden, crack, or lose elasticity due to heat, oil exposure, and mechanical wear. A failed input shaft seal can lead to:
• Transmission fluid leaks
• Low fluid levels
• Increased gearbox noise
• Premature wear on gears and bearings
• Potential drivetrain damage

Replacing worn or leaking seals restores proper fluid containment and protects the integrity of the transmission system, preserving performance and reducing the risk of costly repairs.

Replace the input shaft seal if you notice:
• Visible transmission fluid leaks at the bellhousing area
• Low transmission fluid levels
• Gearbox whine or unusual noises
• Transmission slipping or crunching in gear shifts
• After transmission removal or overhaul

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99911332641

99911332641

99911332640

The product you are viewing cross references to these numbers

3 3 3

Main shaft seal. Porsche 911/912 1972-86

99911332740/1

Product Information

Main shaft seal, 23 x 35 x 8/11.
A rubber shaft oil seal (radial seal) for the main/input shaft of a 901/915-series gearbox. It fits around the rotating shaft and seals the interface between the rotating shaft and the gearbox housing to prevent gearbox oil leaks.
Dimensions: 23 mm (shaft diameter) × 35 mm (outer diameter) × 8/11 mm thickness (seal housing/dual-lip design).

Fits:
Porsche 911 1972 - 1973 (TYP 915) from:
G 733 7575 >>
G 723 0507 >>
G 783 0838 >>
Porsche 911 Carrera 1973 - 1986

Diagram ref no 11

This seal prevents gearbox oil from escaping around the input or main shaft, ensuring the transmission remains properly lubricated. It also blocks dirt, water, and other contaminants from entering the gearbox, helping preserve internal components and maintain correct operating pressure. By replacing a worn, hardened, or cracked original seal, it restores a clean, leak-tight barrier for reliable long-term gearbox performance.

Original gearbox seals degrade over time: rubber lips harden or crack, springs lose tension, and sealing surfaces wear. A failing main-shaft seal typically leads to:
• Gearbox oil leaks
• Loss of gearbox oil over time (low oil level)
• Contamination ingress (dirt, water), leading to accelerated gearbox wear or internal damage
• Messy drip underneath the car and gearbox housing

Replacing the seal with a correct-spec new unit restores proper sealing, preserves gearbox oil integrity, and helps prevent costly internal damage or gearbox failure.

You should replace this seal if:
• Gearbox oil leaks are visible around the input shaft or bellhousing area
• There is seepage, oil dripping, or a film of oil on the underside of gearbox or clutch area
• The old seal appears cracked, hardened, or visibly damaged
• You are doing a gearbox rebuild, overhaul or maintenance
• You notice loss of gearbox oil or suspect contamination ingress

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99911332740

99911332740

91530238100

99911328340

The product you are viewing cross references to these numbers

3 3 3

Differential output shaft seal. Porsche 911 / 964 / 993 / 996 / 986 Boxster / 968

99911334741/1

Product Information

Differential output shaft seal. 48 x 68 x 10 mm.
OE Match differential output shaft seal, engineered to replicate the original Porsche component that seals the output shaft on the differential housing. It prevents gear oil from leaking out where the drive axles exit the differential - a critical sealing function in the drivetrain system.
Sold each.

Fits:
Porsche 911 Carrera 3.2L 1984 - 1989
Porsche 911 Turbo 3.3 1978 - 1989
Porsche 964 1989 - 1994
Porsche 993 1995 - 1998
Porsche 996 1998 - 2005
Porsche 986 Boxster 3.2L 2000 - 2004
Porsche 986 968CS 1993 - 1995

Diagram ref no 20

The differential output shaft seal creates a pressure-resistant, low-friction barrier around the rotating driveshaft or axle stub where it exits the differential. It prevents differential oil from escaping the gearbox while allowing rotational movement, helping maintain optimal lubrication of internal gears, bearings, and limited-slip components.

Function: Installed in the differential carrier housing at the output flange, the seal’s elastomer lip bears against the rotating shaft surface, maintaining contact under variable engine speed, gear torque, and temperature conditions. The internal garter spring ensures the lip is held in consistent contact with the shaft surface, helping prevent weeping or drips that can lead to low lubricant levels and accelerated drivetrain wear.

A worn or hard differential output seal can lose its effectiveness over time, leading to leaks, oil drips, and reduced gear oil levels in the differential. Low lubricant can accelerate wear of differential bearings, gears, and limited-slip clutches - ultimately causing expensive internal damage. Replacing the seal with an OE Match component helps preserve proper differential lubrication, reduces contamination of nearby brake and suspension parts with oil, and maintains drivetrain longevity and performance.

When to replace:
• Visible gear oil leakage from the differential area
•  Oil accumulating near the rear of the gearbox or under the car
•  During differential service or rebuild
•  After replacing output shafts/axle flanges
•  Preventive maintenance on high-mile vehicles

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99911334741

99911334740

99911334741

The product you are viewing cross references to these numbers

Enter your VAT number here and click Verify:

Original Porsche Part Genuine Porsche part 99911333140