cross member Genuine Porsche part 99334110105

Cross Member. Front axle.


Fits:
Porsche 993 1995-98

Click 'Zoom in' for large parts diagram.
Diagram ref no 1

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99334110105

The product you are viewing cross references to these numbers

Steering Rack Mount Reinforcement. It includes the billet anodized aluminum strut and 2 new mounting bolts.



Fits:
Porsche 964
Porsche 993

This kit was originally designed by Porsche and fitted to the 993's that came with the optional 18" wheels.
It is a recommended upgrade for any '92-'98 964/993 car regardless of tire size.

Please Note: The steering racks on 89-91 964 are different then later 964 and 993 cars. The hydraulic lines slightly interfere with the placement of the brace so the lines need to be gently pushed/ bent and the brace needs mount with the flush side down to accommodate.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

RS-160

The product you are viewing cross references to these numbers

Wheel carrier, Front


Fits:
Porsche 993 Carrera RS
Porsche 993 GT 2

Click 'Zoom in' for large parts diagram.
Diagram ref no 1

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99334115

The product you are viewing cross references to these numbers

Toothed ring speed / ABS sensor - Front axle.

Fits:
Porsche 993 1994

Diagram ref no 14

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99334115500

The product you are viewing cross references to these numbers

Elephant Racing 993 RS Uprights.



Fits:
Porsche 964 / 993 1989-98
Use With RS/GT2 Type Tie Rods

Special front uprights (wheel carriers) were equipped on the 993 RS and cup cars, correctly called RS uprights but sometimes called GT2 uprights or EVO uprights. The reason for RS uprights is to correct undesired geometry changes caused by running a lower ride height.

RS upright advantages include improved suspension travel, superior camber gain, and reduced bump steer. The result is superior performance and ride quality.

RS uprights are an awesome upgrade for any lowered 993 or 964 including C2, C4 and Turbo.

Available Now!

Elephant Racing designed RS uprights faithfully reproduce the factory RS geometry. They are made of aircraft grade 7075 aluminum billet for superior strength. They are a direct replacement for the factory 993 RS uprights.
They accept standard 993 front wheel bearings and cover plates. GT2 type tie rods are required.

993 RS Upright vs Standard Upright Differences. There are three basic differences between RS uprights and standard uprights:
• The wheel bearing has been moved up about 30mm relative to the ball joint
• The steering knuckle is relocated and has inverted mounting of the tie rod
• RS uprights are aluminium as are standard 993 uprights. 964 standard uprights are steel.


993 RS Upright Geometry Correction. Lowering a 993 with stock uprights causes several undesired geometry changes, all of which are corrected by the RS uprights.

RS uprights improve camber gain. The lower control arm angles up at the ball joint end, putting the suspension in a poor point on the camber curve. RS uprights angle the lower control arm back down, thus enhancing camber gain and ride quality.

RS uprights improve suspension travel. Lowering the car compresses the front strut and reduces available suspension travel. The result is premature bottoming out, poor handling and ride quality caused by contact with the bump stop – which creates an abrupt and unsettling rise in spring rate at that corner that unsettles the car. RS uprights put back suspension travel.

RS uprights reduce bump steer. Lowering the car moves the stock tie rod into an unfavourable position on the bump steer curve, make the car a handful to drive over uneven surfaces and requiring frequent adjustments at the steering wheel to maintain a steady trajectory. RS uprights relocate the tie rod end placing bump steer in a favourable position on the curve at lowered ride height.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

239000

The product you are viewing cross references to these numbers

Crossbeam bearing, Front.



Fits:
Porsche 993 1994-98

Click 'Zoom in' for large parts diagram.
Diagram ref no 6

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99334111

The product you are viewing cross references to these numbers

Steering Rack Mount Reinforcement. It includes the billet anodized aluminum strut and 2 new mounting bolts.



Fits:
Porsche 964
Porsche 993
Fits all RHD or LHD cars

This kit was originally designed by Porsche and fitted to the 993's that came with the optional 18" wheels.
It is a recommended upgrade for any '92-'98 964/993 car regardless of tire size.

Please Note: The steering racks on 89-91 964 are different then later 964 and 993 cars. The hydraulic lines slightly interfere with the placement of the brace so the lines need to be gently pushed/ bent and the brace needs mount with the flush side down to accommodate.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

3602101601

The product you are viewing cross references to these numbers

Front wheel carrier / hub assembly. 

Fits:
Porsche 993 Carrera 1994-98
Porsche 993 Turbo 1995-98 

NOTE: This part is not compatible with Carrera RS or GT2 models, as they require a different part number.

Diagram ref. 1.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99334115

The product you are viewing cross references to these numbers