Shaft sealing ring. Porsche 993 / 996 / 997 / 991  ❭  99911345441

Gearbox gasket set, for G50 Gearbox
Set of gaskets & seals for gearbox overhaul.

Fits:
Porsche 911 3.2 Carrera 1987-89
Porsche 964 C2 / Carrera RS / Turbo 1989-94 2WD
Porsche 993 1995-98

This Gasket set is engineered for manual G50 gearboxes in Porsche 911 (G-series), 964 and 993 models. A complete kit of gaskets and seals, designed to match original specifications allowing you to service or rebuild your transmission.

A complete gasket set is especially important during rebuilds or overhauls. When the gearbox case is opened or components like bearings and synchros are replaced, new seals ensure the reassembly meets factory specifications and eliminates the risk of post-service leaks.

This product supersedes Porsche's old part numbers:
- 95030091150
- 95030091100

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

96430091200

The product you are viewing cross references to these numbers

Transmission Cover Gasket.



Fits:
Cars with Manual Gearbox
Porsche 911 1987-89 G50 Gearbox
Porsche 964 1989-94
Porsche 993 1995-98

Click 'Zoom in' for large parts diagram.
Diagram ref no 31

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

95030135102

The product you are viewing cross references to these numbers

Manual transmission main shaft seal. 26.5 x 40 mm.
Its function is to act as a primary seal to retain oil around the input (main) shaft of a manual transmission, preventing fluid leaks and protecting driveline components.

Fits:
Porsche 911 Carrera / Turbo 1987 - 1989
Porsche 964 Carrera / Turbo 1989 - 1994
Porsche 993 Carrera / Turbo 1995 - 1998
Porsche 996 Turbo / GT2 / GT3 2001 - 2005
Porsche 997.1 Turbo / GT2 2007 - 2009
Porsche 997.2 Turbo / GT2 2010 - 2013
Porsche 996 GT3 1999 - 2005
Porsche 997 GT3 2007 - 2011

Diagram ref no 12

Application:
• Manual transmission input shaft oil seal
• Cross-referenced with superseded part number: 99911332640

The input shaft seal sits around the input/main shaft where it enters the transmission case. Its job is to keep transmission fluid from leaking out and to prevent contamination from entering the gearbox. By maintaining a secure seal around the rotating shaft, this component helps preserve optimal lubrication, reduce wear, and support smooth gear operation.

In a manual transmission, the input shaft takes power from the clutch and delivers it into the gearbox. The seal must endure rotation, pressure changes, heat, and exposure to transmission fluid, forming a durable barrier that keeps oil inside while preventing dirt and debris from entering. A properly functioning input shaft seal is crucial for transmission longevity and performance.

Over time and mileage, seals can harden, crack, or lose elasticity due to heat, oil exposure, and mechanical wear. A failed input shaft seal can lead to:
• Transmission fluid leaks
• Low fluid levels
• Increased gearbox noise
• Premature wear on gears and bearings
• Potential drivetrain damage

Replacing worn or leaking seals restores proper fluid containment and protects the integrity of the transmission system, preserving performance and reducing the risk of costly repairs.

Replace the input shaft seal if you notice:
• Visible transmission fluid leaks at the bellhousing area
• Low transmission fluid levels
• Gearbox whine or unusual noises
• Transmission slipping or crunching in gear shifts
• After transmission removal or overhaul

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99911332641

The product you are viewing cross references to these numbers