Monoball Sealed front suspension top mounts Rebuild Kit - Front. Porsche 911/912/930  ❭  MB21

Rennline Sealed Front Camber Plates.
SET OF 2

Fits
Porsche 996 C2 3.4L / 3.6L 1998-2005 (2 Wheel Drive)
Porsche 986 Boxster 1997-04

Under extreme conditions, such as road racing and autocross, negative camber is required to keep as much of the tire's contact patch on the road as possible. Stock suspension mounts will not allow you to achieve the necessary amount of negative camber required for this type of performance driving. Rennline's sealed camber plates incorporate FK motorsports spherical bearings and eliminate the indistinct feedback associated with factory rubber mounts. Comes as a set of two. Why are Rennline's strut mounts the best ?

* Drastically increased bearing life due to the integrated factory GT3 weather seals.
* FK Motorsport Teflon-lined spherical bearings.
* Rigid bearing mount, not clipped in like some products available.
* Specially machined upper nut to allow clearance for maximum negative camber settings.
* Allows for up to 1.25 degrees of added negative camber.
* Special tool included to hold strut shaft from turning when tightening upper nut.
* Can be used with all factory and aftermarket struts, Including factory non adjustable units.
* Webbed machined base for light weight and superior strength.
* Fully rebuildable
* CNC machined 6061 anodized aluminum construction with stainless steel hardware.


Note: When using factory non adjustable struts with factory spring seats, weather seal must be remove

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

S20

The product you are viewing cross references to these numbers

QuickChange™ Camber Plates.
Sold per kit, 1 kit req'd per car.




Porsche 996 / 997 C2 models 1999-2012
Porsche 986 / 987 1997-12

Elephant Racing's QuickChange™ Camber plates offer true ease of adjustment. The "slider" design allows a full range of adjustment without the need for removing and rotating the plate for C2, C4, and Turbo models.

More Camber
Range of adjustment is extreme, with 19mm of added travel. This delivers over 2 degrees of added camber, allowing even DOT-R tires and slicks to produce maximum grip.

QuickChange Camber Plate for C4 and Turbo Models
The Quickchange camber plates are available for C2, C4 and Turbo models and work with stock-type springs and coilovers. They will not raise ride height when used with stock-type springs.

Higher Performance
Spherical bearings further improve performance. The spherical bearings pivot freely, but eliminate the deflection that is inherent with the factory rubber bushings. This is important for two reasons;

– The factory rubber acts as a spring in series with the strut. This rubber spring-action is completely un-damped and reduces the struts ability to control the tire contact patch. The spherical bearing allows the strut damper to do its job and control the contact patch.

– The factory rubber deflects sideways under cornering loads, causing loss of camber just when you need it most. Our spherical bearings eliminate the deflection, maintaining stable and predictable camber.

Fully Weather Sealed
The included spherical bearings are oversized, maintenance-free, and PTFE lined – they never need lubrication.
Integrated weather seals on both bottom and top of the spherical bearing extend bearing life. Dirt and water enter competing non-sealed products to accelerate bearing wear. Worse yet are bottom-only seals that can actually trap water that enters the open bearing top!

Our weather seals are fully compatible with coilovers and stock type springs.

Use Stock Springs or Coilovers
Fully compatible with stock springs and aftermarket lowering springs. Also supports coilovers that use and upper spring perch.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

2152205

The product you are viewing cross references to these numbers

Strut top mount monoball cartridge.

1 kit required per axle



Fits
Porsche 986 Boxster - Front and Rear
Porsche 987 Boxster - Front and Rear
Porsche 987 Cayman - Front and Rear
Porsche 996 - Front Only
Porsche 997 - Front Only

Cartridges install easily to replace rubber bushings for 996/997/Boxster/Cayman. An excellent alternative to our QuickChange Camber Plates for cars that don't need more camber but still want the handling precision of a spherical bearing monoball. Spherical bearings improve performance. The spherical bearings pivot freely, but eliminate the deflection that is inherent with the factory rubber bushings.

Eliminating Deflection Is Important For Two Reasons

• The factory rubber acts as a spring in series with the strut. This rubber spring-action is completely un-damped and reduces the struts ability to control the tire contact patch. The spherical bearing allows the strut damper to do its job and control the contact patch.
• The factory rubber deflects sideways under cornering loads, causing loss of camber just when you need it most. Our spherical bearings eliminate the deflection, maintaining stable and predictable camber.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

2011002

The product you are viewing cross references to these numbers