Enter your VAT number here and click Verify:
Your details have been verified. VAT number registered to:
,
.
Your order will now be zero rated for VAT purposes. We reserve the right to verify these details after your order request has been made and reinstate VAT if required.
Your VAT details were not recognised or were invalid. Your VAT number must be matched to your Billing Country as specified above. This is currently specified as . You do not need to enter the country code part of your VAT number as this has already been selected in your billing address details above.
The VAT number checking service is currently offline. Please supply your VAT details within the comments or special instructions field below and we will apply a VAT discount after placing your order request.
Select your vehicle to check compatibility
OE Match
99911308540/1
Product Information
OE Match rear wheel bearing outer seal engineered to replicate the original factory sealing component used on early Porsche 911 and 912 models (1965–1968). It is designed to fit into the wheel hub to seal the outer side of the rear wheel bearing, keeping lubricant in and contaminants out.
Sold per each, 2 required per car.
Fits:
Porsche 911 2.0 01/1963 - 07/1968
Porsche 912 1.6 01/1965 - 07/1968
Diagram Ref No 10
The rear wheel bearing outer seal prevents lubricant loss from the wheel hub and keeps dirt, water, and debris out of the bearing assembly. By maintaining correct lubrication and preventing contamination, the seal helps ensure smooth bearing rotation and prolongs the service life of the wheel bearings.
Function:
Installed on the outer side of the rear wheel hub, this seal:
• Retains bearing lubricant inside the hub assembly
• Keeps water, mud, dust, and road contaminants out
• Protects internal bearing surfaces from corrosion and wear
• Maintains correct contact with the rotating bearing outer race
Accurate lip geometry and correct seal dimensions are essential to form a tight sealing interface while accommodating hub rotation and slight shaft movement.
Wheel bearing seals protect the integrity of the bearing assembly - a critical rotational component subjected to high loads, speed, and road conditions. A worn, cracked, or leaking seal can allow grease to escape and contaminants to enter, resulting in accelerated bearing wear, noise, vibration, and ultimately bearing failure. Installing fresh OE Match seals helps preserve bearing lubrication and contributes to smooth, quiet rear wheel rotation and long service life.
When to replace:
• During wheel bearing service or rebuild
• If seal lip is cracked, hardened, or visibly worn
• When grease appears contaminated, leaking, or lost
• After water exposure or road debris impact
• As preventive maintenance on unrestored classic vehicles
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
99911308540
The product you are viewing cross references to these numbers
Product Information
Rear wheel bearing seal outer. DG 62 x 68 x 6 / 10. OE Match rear wheel bearing outer seal engineered to replicate the original factory sealing component used on early Porsche 911 and 912 models (1965–1968). It is designed to fit into the wheel hub to seal the outer side of the rear wheel bearing, keeping lubricant in and contaminants out.
Sold per each, 2 required per car.
Fits:
Porsche 911 2.0 01/1963 - 07/1968
Porsche 912 1.6 01/1965 - 07/1968
Diagram Ref No 10
The rear wheel bearing outer seal prevents lubricant loss from the wheel hub and keeps dirt, water, and debris out of the bearing assembly. By maintaining correct lubrication and preventing contamination, the seal helps ensure smooth bearing rotation and prolongs the service life of the wheel bearings.
Function:
Installed on the outer side of the rear wheel hub, this seal:
• Retains bearing lubricant inside the hub assembly
• Keeps water, mud, dust, and road contaminants out
• Protects internal bearing surfaces from corrosion and wear
• Maintains correct contact with the rotating bearing outer race
Accurate lip geometry and correct seal dimensions are essential to form a tight sealing interface while accommodating hub rotation and slight shaft movement.
Wheel bearing seals protect the integrity of the bearing assembly - a critical rotational component subjected to high loads, speed, and road conditions. A worn, cracked, or leaking seal can allow grease to escape and contaminants to enter, resulting in accelerated bearing wear, noise, vibration, and ultimately bearing failure. Installing fresh OE Match seals helps preserve bearing lubrication and contributes to smooth, quiet rear wheel rotation and long service life.
When to replace:
• During wheel bearing service or rebuild
• If seal lip is cracked, hardened, or visibly worn
• When grease appears contaminated, leaking, or lost
• After water exposure or road debris impact
• As preventive maintenance on unrestored classic vehicles
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
99911308540
1651250100
The product you are viewing cross references to these numbers
Vehicle Group
Vehicle Group
- Porsche 911 1965-1968 2.0L / 912 SWB (F)
£6.90 inc. VAT
Now £6.21 inc. VAT
In Stock - 24 Hour Dispatch
Also found on these pages