Oxygen Sensor Extension with additional filter mesh for Porsche - 00060612302
Koblenz
00060612302
Product Information
Important: Make sure there is enough clearance before ordering and fitting this item.
Having problems with your Check Engine Light?
Want to run Cat Bypass pipes or a free flowing sports catalyst set up on your vehicle without having to reprogram the DME (ECU)?
Our adapter offsets the oxygen sensor about 1.5 inch from the gas stream. This achieves, in most cases, a sufficient measurement for the air/CO ratio and increases the tolerance range between the pre and post cat oxygen sensors. In addition, the sensitivity of the oxygen sensor is also reduced allowing you to run a nearly any exhaust or catalytic set up, including bypass pipes, without the need to reprogram your ECU!
Only used for the 2nd oxygen sensor (after catalytic). Should only be installed by tuners
Price shown is for each
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
00060612302
The product you are viewing cross references to these numbers
Product Information
Oxygen Sensor Extension with additional filter mesh for PorscheImportant: Make sure there is enough clearance before ordering and fitting this item.
Having problems with your Check Engine Light?
Want to run Cat Bypass pipes or a free flowing sports catalyst set up on your vehicle without having to reprogram the DME (ECU)?
Our adapter offsets the oxygen sensor about 1.5 inch from the gas stream. This achieves, in most cases, a sufficient measurement for the air/CO ratio and increases the tolerance range between the pre and post cat oxygen sensors. In addition, the sensitivity of the oxygen sensor is also reduced allowing you to run a nearly any exhaust or catalytic set up, including bypass pipes, without the need to reprogram your ECU!
Only used for the 2nd oxygen sensor (after catalytic). Should only be installed by tuners
Price shown is for each
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
00060612302
00060612302
The product you are viewing cross references to these numbers
Vehicle Group
Vehicle Group
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche Boxster 987 2.7L 2005 -08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche Boxster 987 MKII 2.9L 2009-2012
- Porsche Boxster S 987 MKII 3.4L 2009-2012
- Porsche Boxster 981 2.7L 2012-16
- Porsche Boxster S 981 3.4L 2012-16
- Porsche Boxster Spyder 3.8L 2016
- Porsche Boxster 718 2.0L Manual (300 Bhp)
- Porsche Boxster 718 2.0L PDK (300 Bhp)
- Porsche Boxster S 718 2.5L Manual (350 Bhp)
- Porsche Boxster S 718 2.5L PDK (350 Bhp)
- Porsche Boxster T 718 2.0L Manual (300 Bhp)
- Porsche Boxster T 718 2.0L PDK (300 Bhp)
- Porsche Boxster GTS 718 2.5L Manual (365 Bhp)
- Porsche Boxster GTS 718 2.5L PDK (365 Bhp)
- Porsche Boxster GTS 718 4.0L Manual (400 Bhp)
- Porsche Boxster GTS 718 4.0L PDK (400 Bhp)
- Porsche Boxster Spyder 718 4.0L (420 Bhp)
- Porsche Boxster 25 Years 718 4.0L Manual (400 Bhp)
- Porsche Boxster 25 Years 718 4.0L PDK (400 Bhp)
- Porsche 993 (911) C2 1994-97
- Porsche 993 (911) C4 1994-97
- Porsche 993 (911) RS 1994-97
- Porsche 993 (911) C2S 1994-97
- Porsche 993 (911) C4S 1994-97
- Porsche 993 (911) TURBO 1994-96
- Porsche 993 (911) GT2 1994-97
- Porsche 993 (911) TURBO S 1994-97
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 TURBO 2000-05
- Porsche 996 GT2 2001-05
- Porsche 996 GT3 MKI 1999-02
- Porsche 996 GT3 MKII 2003>>
- Porsche 996 GT3 RS 2003-04
- Porsche 997 Carrera 2 3.6L 2005>>
- Porsche 997 Carrera 2S 3.8L 2005>>
- Porsche 997 Carrera 4 3.6L 2005>>
- Porsche 997 Carrera 4S 3.8L 2005>>
- Porsche 997 TURBO 2007>>
- Porsche 997 GT3 2007>>
- Porsche 997 GT2 2007>>
- Porsche 997 MKII Carrera C2 3.6L 2009>>
- Porsche 997 MKII Carrera C4 3.6L 2009>>
- Porsche 997 MKII Carrera C2S 3.8L 2009>>
- Porsche 997 MKII Carrera C4S 3.8L 2009>>
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 R 4.0L (500 Bhp)
- Porsche 991 GT3 3.8L (475Bhp)
- Porsche 991 GT3 RS 4.0L (500Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
- Porsche 991 Speedster 4.0L (510Bhp)
- Porsche 991 GT3 4.0L (500 Bhp) / GT3 RS 4.0L (520 Bhp)
- Porsche 991 GT2 RS 3.8L PDK (700 bhp)
- Porsche Cayman 2.7L 987C 2006-08
- Porsche Cayman S 3.4L 987C 2005-08
- Porsche Cayman 2.9L 987C MKII 2009-12
- Porsche Cayman S / R 3.4L 987C MKII 2009-12
- Porsche Cayman 2.7L 981 2013-16
- Porsche Cayman S 3.4L 981 2013-16
- Porsche Cayman GT4 3.8L 2015-16
- Porsche Cayman 718 2.0L Manual (300Bhp)
- Porsche Cayman 718 2.0L PDK (300Bhp)
- Porsche Cayman S 718 2.5L Manual (350Bhp)
- Porsche Cayman S 718 2.5L PDK (350Bhp)
- Porsche Cayman T 718 2.0L Manual (300Bhp)
- Porsche Cayman T 718 2.0L PDK (300 Bhp)
- Porsche Cayman GTS 718 2.5L Manual (365 Bhp)
- Porsche Cayman GTS 718 2.5L PDK (365 Bhp)
- Porsche Cayman GTS 718 4.0L Manual (400 Bhp)
- Porsche Cayman GTS 718 4.0L PDK (400 Bhp)
- Porsche Cayman GT4 718 4.0L / GT4 RS 718 4.0L
- Porsche Cayman GT4 Clubsport
- Porsche Cayman GT4 RS Clubsport 2020-2024
€53.10 inc. VAT
Now €47.79 inc. VAT
In Stock - 24 Hour Dispatch
Shop Securely
12 Month Warranty
Worldwide Delivery
Related products
FSO2CAT90P
Product Information
Product Details:
Universal O2 Spacers with Catalytic Converters scrub the exhaust and lengthen the distance between the O2 sensor(s) and the exhaust flow to reduce the chance of a CEL.
We've taken our O2 spacers a step further. The factory ECU compares the readings from a pair of oxygen sensors to measure the effectiveness of the catalysts. When a high-flow cat or catbypass pipe is used the exhaust gases reach the O2 sensor faster and uncleaned, leading to high chances to throw a CEL. Our O2 spacers retract the secondary oxygen sensors from the direct flow of gases, restoring the balance that the ECU requires when using aftermarket catalysts or catbypass pipes. The high quality built in catalysts scrub the exhaust to further reduce the chance of a CEL. Two fitting options and the two piece design allow for adjustment to get best possible fitment and results.
FEATURES:
Fits most makes & models worldwide
Compatible with all Fabspeed Motorsport header, Sport Cat, and Catbypass products
Minimizes the triggering of the CEL by moving the O2 sensor further from the exhaust stream and scrubbing exhaust
Male end threads into existing M18 x 1.5 O2 Bungs
Spacer body dimensions: 3 3/4" L x 1 1/2" W x 1 1/2" H
Fitting dimensions: 1" L x 1" W x 1" H (not including threaded portion)
1" depth of threads on fittings for adjustments
IMPORTANT NOTES:
For use on downstream oxygen sensors only
This product cannot guarantee emissions compliance
Universal fitment
Product Information
Fabspeed Universal 90 Degree O2 spacers with catalytic convertersProduct Details:
Universal O2 Spacers with Catalytic Converters scrub the exhaust and lengthen the distance between the O2 sensor(s) and the exhaust flow to reduce the chance of a CEL.
We've taken our O2 spacers a step further. The factory ECU compares the readings from a pair of oxygen sensors to measure the effectiveness of the catalysts. When a high-flow cat or catbypass pipe is used the exhaust gases reach the O2 sensor faster and uncleaned, leading to high chances to throw a CEL. Our O2 spacers retract the secondary oxygen sensors from the direct flow of gases, restoring the balance that the ECU requires when using aftermarket catalysts or catbypass pipes. The high quality built in catalysts scrub the exhaust to further reduce the chance of a CEL. Two fitting options and the two piece design allow for adjustment to get best possible fitment and results.
FEATURES:
Fits most makes & models worldwide
Compatible with all Fabspeed Motorsport header, Sport Cat, and Catbypass products
Minimizes the triggering of the CEL by moving the O2 sensor further from the exhaust stream and scrubbing exhaust
Male end threads into existing M18 x 1.5 O2 Bungs
Spacer body dimensions: 3 3/4" L x 1 1/2" W x 1 1/2" H
Fitting dimensions: 1" L x 1" W x 1" H (not including threaded portion)
1" depth of threads on fittings for adjustments
IMPORTANT NOTES:
For use on downstream oxygen sensors only
This product cannot guarantee emissions compliance
Universal fitment
€429.82 inc. VAT
Now €386.84 inc. VAT
In Stock - 24 Hour Dispatch
Shop Securely
12 Month Warranty
Worldwide Delivery
99900010035
Product Information
With the OBD killer we have created a universal solution.
The device cyclically checks for pending and permanent error codes and deletes them.
Error codes or entire classes can be isolated on request.
If an error occurs outside of the expected error classes, the deletion process stops.
Thus, the functionality of the fault memory is maintained.
We present the new generation of the OBD Killer
Teachable
The new OBD killer learns the entered error codes and is therefore suitable for all emission-related, sporadic errors
Automatically
While driving, the engine control unit is monitored for sporadic errors in real time
Fast
Already existing error codes are blocked
Even before an error message is entered
Universal
For almost all vehicles from 2008
(some earlier cars may be supported)
What is the OBD Killer?
"OBD" stands for "on-board diagnostics", the standardized diagnostic interface of motor vehicles.
The OBD Killer is a compact electronics module, which is simply plugged into this diagnostic port.
There it will monitor the error messages of the engine control unit in real time for possible entries.
If a pending error is detected in memory, the OBD Killer blocks it before the driver sees a message on the Instrument Cluster/Check Engine "MIL" is Illuminated.
As soon as there is an error messages of no concern registered, the OBD Killer intervenes immediately,
removes the pending error message before it comes to an entry in the actual fault memory.
If an error code has already been entered before using the OBD killer, it will also be removed.
For which vehicles is the OBD Killer suitable?
The OBD killer can be used on all vehicles from model year 2008.
There are also vehicles that already support the necessary standard in the years before.
These vehicles can be recognized if pins 6 and 14 are occupied at the OBD diagnostic port.
It does not matter if the engine is diesel, gas, natural gas or LPG.
Some engine control units do not support the deletion of fault codes while driving.
For these vehicles, the OBD killer is then not suitable.
Which mistakes does the OBD Killer block?
The OBD killer is capable of learning can generally block all emission-related error codes.
During installation, the OBD killer learns the registered codes as expected errors. This process can be repeated as often as you like.
One of the most common mistakes is e.g. in connection with coked EGR valves code P0401. and the error code P0420 occurs very frequently e.g. aged catalysts.
It also deletes vendor-specific codes that do not conform to the OBD standard.
As soon as there is an error message that has not been "Taught/Programmed", the OBD killer will not intervene.
Thus, the full functionality of fault memory and engine indicator light is retained for all other error messages.
Where is the OBD Killer used?
The OBD killer is ideal for all sporadically occurring, exhaust-related errors such. P0400, P0401, P0402, P0403, P0404, P0405, P0406, P0407, P0408 (exhaust gas recirculation): After a repair of the exhaust gas recirculation, sporadic error messages often occur which often cannot be adequately clarified. The OBD killer is here a cheap alternative to the multiple replacement of all components.
Otherwise the error class of the catalyst (P0420, P0421, P0422, P0423, P0424, P0430, P0431, P0432, P0433, P0434).
Often the engine control unit repeatedly reports a faulty catalytic converter, although it is still in order.
This comes, for example, when using sports catalysts.
For performance increases or unexplained turbocharger problems often occurs the error code P0234: Boost pressure limit exceeded.
What do I do when changing vehicles?
When changing the vehicle, you can continue to use the OBD killer for all vehicles from the year 2008 onwards.
If the OBD killer detects a new chassis number after installation, all learned values will be reset.
The OBD killer then acts as brand new.
Will repairs become superfluous?
No.
If a repair has already been carried out for a fault, but then returns prematurely or reoccurs too frequently or cannot be solved or if no fault was found during diagnostics.
Instead of replacing all the parts again, the OBD killer is the better solution for the wallet and protects the environmental resources.
NB. OBD Killer is not able to display Fault codes and is purely "Taught" which codes to block by plugging the unit into the diagnostic socket, unplugging then plugging back in again. At this point whatever fault code was logged will be blocked or deleted by the OBD Killer. A generic Code reader capable of displaying engine fault codes would be needed when "Teaching" the OBD Killer to check which codes you are teaching it to block/delete.
Only "Teach" codes you know will not harm your vehicle.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
99900010035
The product you are viewing cross references to these numbers
Product Information
You know the problem: modern engine control units can react to even the smallest changes to the system and register fault codes.With the OBD killer we have created a universal solution.
The device cyclically checks for pending and permanent error codes and deletes them.
Error codes or entire classes can be isolated on request.
If an error occurs outside of the expected error classes, the deletion process stops.
Thus, the functionality of the fault memory is maintained.
We present the new generation of the OBD Killer
Teachable
The new OBD killer learns the entered error codes and is therefore suitable for all emission-related, sporadic errors
Automatically
While driving, the engine control unit is monitored for sporadic errors in real time
Fast
Already existing error codes are blocked
Even before an error message is entered
Universal
For almost all vehicles from 2008
(some earlier cars may be supported)
What is the OBD Killer?
"OBD" stands for "on-board diagnostics", the standardized diagnostic interface of motor vehicles.
The OBD Killer is a compact electronics module, which is simply plugged into this diagnostic port.
There it will monitor the error messages of the engine control unit in real time for possible entries.
If a pending error is detected in memory, the OBD Killer blocks it before the driver sees a message on the Instrument Cluster/Check Engine "MIL" is Illuminated.
As soon as there is an error messages of no concern registered, the OBD Killer intervenes immediately,
removes the pending error message before it comes to an entry in the actual fault memory.
If an error code has already been entered before using the OBD killer, it will also be removed.
For which vehicles is the OBD Killer suitable?
The OBD killer can be used on all vehicles from model year 2008.
There are also vehicles that already support the necessary standard in the years before.
These vehicles can be recognized if pins 6 and 14 are occupied at the OBD diagnostic port.
It does not matter if the engine is diesel, gas, natural gas or LPG.
Some engine control units do not support the deletion of fault codes while driving.
For these vehicles, the OBD killer is then not suitable.
Which mistakes does the OBD Killer block?
The OBD killer is capable of learning can generally block all emission-related error codes.
During installation, the OBD killer learns the registered codes as expected errors. This process can be repeated as often as you like.
One of the most common mistakes is e.g. in connection with coked EGR valves code P0401. and the error code P0420 occurs very frequently e.g. aged catalysts.
It also deletes vendor-specific codes that do not conform to the OBD standard.
As soon as there is an error message that has not been "Taught/Programmed", the OBD killer will not intervene.
Thus, the full functionality of fault memory and engine indicator light is retained for all other error messages.
Where is the OBD Killer used?
The OBD killer is ideal for all sporadically occurring, exhaust-related errors such. P0400, P0401, P0402, P0403, P0404, P0405, P0406, P0407, P0408 (exhaust gas recirculation): After a repair of the exhaust gas recirculation, sporadic error messages often occur which often cannot be adequately clarified. The OBD killer is here a cheap alternative to the multiple replacement of all components.
Otherwise the error class of the catalyst (P0420, P0421, P0422, P0423, P0424, P0430, P0431, P0432, P0433, P0434).
Often the engine control unit repeatedly reports a faulty catalytic converter, although it is still in order.
This comes, for example, when using sports catalysts.
For performance increases or unexplained turbocharger problems often occurs the error code P0234: Boost pressure limit exceeded.
What do I do when changing vehicles?
When changing the vehicle, you can continue to use the OBD killer for all vehicles from the year 2008 onwards.
If the OBD killer detects a new chassis number after installation, all learned values will be reset.
The OBD killer then acts as brand new.
Will repairs become superfluous?
No.
If a repair has already been carried out for a fault, but then returns prematurely or reoccurs too frequently or cannot be solved or if no fault was found during diagnostics.
Instead of replacing all the parts again, the OBD killer is the better solution for the wallet and protects the environmental resources.
NB. OBD Killer is not able to display Fault codes and is purely "Taught" which codes to block by plugging the unit into the diagnostic socket, unplugging then plugging back in again. At this point whatever fault code was logged will be blocked or deleted by the OBD Killer. A generic Code reader capable of displaying engine fault codes would be needed when "Teaching" the OBD Killer to check which codes you are teaching it to block/delete.
Only "Teach" codes you know will not harm your vehicle.
Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.
99900010035
99900010035
The product you are viewing cross references to these numbers
Vehicle Group
Vehicle Group
- Porsche Boxster 986 2.5L 1997-99
- Porsche Boxster 986 2.7L 1999-02
- Porsche Boxster S 986 3.2L 1999-02
- Porsche Boxster 986 2.7L 2003-04
- Porsche Boxster S 986 3.2L 2003-04
- Porsche Boxster 987 2.7L 2005 -08/08
- Porsche Boxster 987 S 3.2/3.4L 2005-08/08
- Porsche Boxster 987 MKII 2.9L 2009-2012
- Porsche Boxster S 987 MKII 3.4L 2009-2012
- Porsche Boxster 981 2.7L 2012-16
- Porsche Boxster S 981 3.4L 2012-16
- Porsche Boxster 718 2.0L Manual (300 Bhp)
- Porsche Boxster 718 2.0L PDK (300 Bhp)
- Porsche Boxster S 718 2.5L Manual (350 Bhp)
- Porsche Boxster S 718 2.5L PDK (350 Bhp)
- Porsche Boxster T 718 2.0L Manual (300 Bhp)
- Porsche Boxster T 718 2.0L PDK (300 Bhp)
- Porsche Boxster GTS 718 2.5L Manual (365 Bhp)
- Porsche Boxster GTS 718 2.5L PDK (365 Bhp)
- Porsche Boxster Spyder 718 4.0L (420 Bhp)
- Porsche 911 1965-1968 2.0L / 912 SWB (F)
- Porsche 911 1968-1973 2.2L / 2.4L / 2.7L RS LWB (F)
- Porsche 911 1974-1977 2.7L / 1976-77 3.0 Carrera
- Porsche 911 1978-1983 3.0L / SC
- Porsche 911 1984-1986 3.2L
- Porsche 911 1987-1989 3.2L G50
- Porsche 911 1975-1977 3.0L Turbo (930)
- Porsche 911 1978-1989 3.3L Turbo (930)
- Porsche 964 (911) C2 1989-93
- Porsche 964 (911) C4 1989-93
- Porsche 964 (911) RS 3.6L 1991-93
- Porsche 964 (911) RS 3.8L 1991-93
- Porsche 964 (911) TURBO 3.3L 1991-93
- Porsche 964 (911) TURBO 3.6L 1991-93
- Porsche 993 (911) C2 1994-97
- Porsche 993 (911) C4 1994-97
- Porsche 993 (911) RS 1994-97
- Porsche 993 (911) C2S 1994-97
- Porsche 993 (911) C4S 1994-97
- Porsche 993 (911) TURBO 1994-96
- Porsche 993 (911) GT2 1994-97
- Porsche 993 (911) TURBO S 1994-97
- Porsche 996 C2 3.4L 1997-08/01
- Porsche 996 C4 3.4L 1997-08/01
- Porsche 996 C2 3.6L 09/01-2005
- Porsche 996 C4 3.6L 09/01-2005
- Porsche 996 C4S 3.6L 09/01-2005
- Porsche 996 TURBO 2000-05
- Porsche 996 GT2 2001-05
- Porsche 996 GT3 MKI 1999-02
- Porsche 996 GT3 MKII 2003>>
- Porsche 996 GT3 RS 2003-04
- Porsche 997 Carrera 2 3.6L 2005>>
- Porsche 997 Carrera 2S 3.8L 2005>>
- Porsche 997 Carrera 4 3.6L 2005>>
- Porsche 997 Carrera 4S 3.8L 2005>>
- Porsche 997 TURBO 2007>>
- Porsche 997 GT3 2007>>
- Porsche 997 GT2 2007>>
- Porsche 997 MKII Carrera C2 3.6L 2009>>
- Porsche 997 MKII Carrera C4 3.6L 2009>>
- Porsche 997 MKII Carrera C2S 3.8L 2009>>
- Porsche 997 MKII Carrera C4S 3.8L 2009>>
- Porsche 997 MKII GT3 2010>>
- Porsche 997 MKII Turbo 2009>>
- Porsche 997 MKII GT2 RS 2011>>
- Porsche 991 Carrera C2 3.4L (350Bhp)
- Porsche 991 Carrera C2S 3.8L (400Bhp)
- Porsche 991 Carrera C4 3.4L (350Bhp)
- Porsche 991 Carrera C4S 3.8L (400Bhp)
- Porsche 991 Turbo 3.8L (520bhp)
- Porsche 991 Turbo S 3.8L (560Bhp)
- Porsche 991 R 4.0L (500 Bhp)
- Porsche 991 GT3 3.8L (475Bhp)
- Porsche 991 GT3 RS 4.0L (500Bhp)
- Porsche 991 Carrera 2 3.0L (370 Bhp)
- Porsche 991 Carrera 2S 3.0L (420 Bhp)
- Porsche 991 Carrera 4 3.0L (370 Bhp)
- Porsche 991 Carrera 4S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 2 3.0L (370 Bhp)
- Porsche 991 Cabriolet 2S 3.0L (420 Bhp)
- Porsche 991 Cabriolet 4 3.0L (370 Bhp)
- Porsche 991 Cabriolet 4S 3.0L (420 Bhp)
- Porsche 991 Targa 4 3.0L (370 Bhp)
- Porsche 991 Targa 4S 3.0L (420 Bhp)
- Porsche 991 Turbo Coupe 3.8L (540 Bhp)
- Porsche 991 Turbo S Coupe 3.8L (580 Bhp)
- Porsche 991 Turbo Cabriolet 3.8L (540 Bhp)
- Porsche 991 Turbo S Cabriolet 3.8L (580 Bhp)
- Porsche 991 Speedster 4.0L (510Bhp)
- Porsche 991 GT3 4.0L (500 Bhp) / GT3 RS 4.0L (520 Bhp)
- Porsche 991 GT2 RS 3.8L PDK (700 bhp)
- Porsche 992 Carrera 2 3.0L
- Porsche 992 Carrera 4 3.0L
- Porsche 992 Carrera 2 Cabriolet 3.0L
- Porsche 992 Carrera 4 Cabriolet 3.0L
- Porsche 992 Carrera 2S 3.0L
- Porsche 992 Carrera 4S 3.0L
- Porsche 992 Carrera 2S Cabriolet 3.0L
- Porsche 992 Carrera 4S Cabriolet 3.0L
- Porsche 992 Targa 4 3.0L
- Porsche 992 Targa 4S 3.0L
- Porsche 992 Speedster 4.0L
- Porsche 992 Turbo 3.8L
- Porsche 992 Turbo S 3.8L
- Porsche 992 Turbo Cabriolet 3.8L
- Porsche 992 Turbo S Cabriolet 3.8L
- Porsche 992 GT3 4.0L / 992 S/T 4.0L
- Porsche Cayman 2.7L 987C 2006-08
- Porsche Cayman S 3.4L 987C 2005-08
- Porsche Cayman 2.9L 987C MKII 2009-12
- Porsche Cayman S / R 3.4L 987C MKII 2009-12
- Porsche Cayman 2.7L 981 2013-16
- Porsche Cayman S 3.4L 981 2013-16
- Porsche Cayman GT4 3.8L 2015-16
- Porsche Cayman 718 2.0L Manual (300Bhp)
- Porsche Cayman 718 2.0L PDK (300Bhp)
- Porsche Cayman S 718 2.5L Manual (350Bhp)
- Porsche Cayman S 718 2.5L PDK (350Bhp)
- Porsche Cayman T 718 2.0L Manual (300Bhp)
- Porsche Cayman T 718 2.0L PDK (300 Bhp)
- Porsche Cayman GTS 718 2.5L Manual (365 Bhp)
- Porsche Cayman GTS 718 2.5L PDK (365 Bhp)
- Porsche Cayman GTS 718 4.0L Manual (400 Bhp)
- Porsche Cayman GT4 718 4.0L / GT4 RS 718 4.0L
- Porsche Carrera GT
- Porsche Cayenne 3.2L V6 2003>>
- Porsche Cayenne S 4.5L V8 2003>>
- Porsche Cayenne Turbo 4.5L 2003>>
- Porsche Cayenne Turbo S 4.5L 2006>>
- Porsche Cayenne 3.0L Diesel 2007>>
- Porsche Cayenne 3.6L 2007>>
- Porsche Cayenne S/GTS 4.8L 2007>>
- Porsche Cayenne Turbo / Turbo S 4.8L 2007>>
- Porsche Cayenne V6 3.6L Petrol 300Hp
- Porsche Cayenne V6 3.0L Diesel 245HP
- Porsche Cayenne S V6 3.0L Hybrid 380HP
- Porsche Cayenne S V8 4.8L Petrol 400HP
- Porsche Cayenne S V8 4.2L Diesel 382HP
- Porsche Cayenne GTS V8 4.8L Petrol 400HP
- Porsche Cayenne Turbo V8 4.8L Petrol 500HP
- Porsche Cayenne Turbo S V8 4.8L Petrol 550HP
- Porsche Cayenne V6 3.0L Petrol 340Hp
- Porsche Cayenne Coupe V6 3.0L Petrol 340Hp
- Porsche Cayenne E-Hybrid V6 3.0L V6 340Hp
- Porsche Cayenne Coupe E-Hybrid V6 3.0L 340Hp
- Porsche Cayenne S V6 2.9L Petrol 440Hp
- Porsche Cayenne Coupe S V6 2.9L Petrol 440Hp
- Porsche Cayenne Turbo V8 4.0L Petrol 550Hp
- Porsche Cayenne Coupe Turbo V8 4.0L Petrol 550Hp
- Porsche Cayenne Turbo S E-Hybrid V8 4.0L 550Hp
- Porsche Cayenne Coupe Turbo S E-Hybrid V8 4.0L 550Hp
- Porsche Panamera V6 3.6L 2WD
- Porsche Panamera 4 V6 3.6L 4WD
- Porsche Panamera S V8 4.8L
- Porsche Panamera 4S V8 4.8L
- Porsche Panamera GTS V8 4.8L
- Porsche Panamera Turbo V8 4.8L
- Porsche Panamera Turbo S V8 4.8L
- Porsche Panamera Diesel V6 3.0L
- Porsche Panamera S Hybrid V6 3.0L
- Porsche Panamera V6 3.6L 2WD (310Hp)
- Porsche Panamera 4 V6 3.6L 4WD (310Hp)
- Porsche Panamera S V6 Turbo 3.0L 2WD (420Hp)
- Porsche Panamera S V6 Turbo 3.0L 2WD Executive
- Porsche Panamera 4S V6 Turbo 3.0L 4WD (420Hp)
- Porsche Panamera 4S V6 Turbo 3.0L 4WD Executive
- Porsche Panamera GTS V8 4.8L 4WD (440Hp)
- Porsche Panamera Turbo V8 4.8L (520Hp)
- Porsche Panamera Turbo V8 Executive
- Porsche Panamera Turbo S V8 4.8L
- Porsche Panamera Diesel V6 3.0L (250Hp)
- Porsche Panamera S E-Hybrid V6 3.0L (416Hp)
- Porsche Panamera V6 3.0L 2WD (330 Hp)
- Porsche Panamera 4 V6 3.0L 4WD (330 Hp)
- Porsche Panamera 4 V6 3.0L 4WD Executive
- Porsche Panamera 4 3.0L Turbocharged V6 Sport Turismo
- Porsche Panamera 4S V6 3.0L 4WD (440 Hp)
- Porsche Panamera 4S V6 3.0L 4WD Executive
- Porsche Panamera 4S 2.9L Twin-Turbo V6 Sport Turismo
- Porsche Panamera 4S Diesel V8 4.0L 4WD (422 Hp)
- Porsche Panamera 4S Diesel 4.0L Twin-Turbo V8 Sport Turismo
- Porsche Panamera 4 E-Hybrid V6 2.9L 4WD
- Porsche Panamera 4 E-Hybrid V6 2.9L 4WD Executive
- Porsche Panamera 4 E-Hybrid 2.9L Twin-Turbo V6 Sport Turismo
- Porsche Panamera Turbo V8 4.0L 4WD (550 Hp)
- Porsche Panamera Turbo V8 4.0L 4WD Executive
- Porsche Panamera Turbo 4.0L Twin-Turbo V8 Sport Turismo
- Porsche Panamera Turbo S E-Hybrid V8 4.0L 4WD
- Porsche Panamera Turbo S E-Hybrid V8 4.0L 4WD Executive
- Porsche Macan Petrol 2.0L 237Bhp
- Porsche Macan S Petrol 3.0L V6 340Bhp
- Porsche Macan S Diesel 3.0L V6 258Bhp
- Porsche Macan GTS Petrol 3.0L V6 360Bhp
- Porsche Macan Turbo 3.6L V6 400Bhp
- Porsche Macan Petrol 2.0L 245Bhp
- Porsche Macan S Petrol 3.0L V6 354Bhp
- Porsche Macan GTS Petrol 2.9L V6 380Bhp
- Porsche Macan Turbo 2.9L V6 440Bhp
- Porsche Taycan 4S
- Porsche Taycan Turbo
- Porsche Taycan Turbo S
- Porsche 918 Spyder 4.6L
- Porsche 924 2.0L 1976-79
- Porsche 924 2.0L 1980-85
- Porsche 924 Turbo 2.0L 1979-81
- Porsche 924 Turbo 2.0L 1982-84
- Porsche 924 Carrera GT 2.0L 1981
- Porsche 924 Carrera GTS 2.0L 1982
- Porsche 924S 2.5L 1986-87
- Porsche 924S 2.5L 1988
- Porsche 944 2.5L 8V 1982-87
- Porsche 944 2.7L 8V 1988-89
- Porsche 944S 2.5L 16V 1987-88
- Porsche 944S2 3.0L 16V 1989-91
- Porsche 944 Turbo 2.5L 8V 1985-88
- Porsche 944 Turbo 2.5L 8V 1989-91
- Porsche 944 Turbo S 2.5L 8V 1988>>
- Porsche 968 3.0L 1992-94
- Porsche 968 Sport 3.0L 1994-95
- Porsche 968 CS 3.0L 1993-95
- Porsche 968 Turbo S 3.0L 1993-94
- Porsche 928 4.5L 1978-82
- Porsche 928S 4.7L 1981-83
- Porsche 928S2 4.7L 1984-86
- Porsche 928S4 5.0L 1987-92
- Porsche 928GT 5.0L 1989-91
- Porsche 928GTS 5.4L 1992-95
- Porsche 356 1950-55
- Porsche 356A 1955-59
- Porsche 356B 1959-63
- Porsche 356C 1963-65
- Porsche 914 (1970-1976)
- Porsche 912E 4CYL 1976
€234.82 inc. VAT
Now €211.34 inc. VAT
In Stock - 3- 5 Days Dispatch
Shop Securely
12 Month Warranty
Worldwide Delivery
FSO2CAT45P
Product Information
Product Details:
There is no guarantee this will prevent a CEL from triggering
Universal O2 spacers with real precious metal Catalytic Converters lengthen the distance between the O2 spacer(s). We've taken our spacers a step further by having built-in catalytic converters to allow the ECU to properly read exhaust gas and perform at optimal performance.
Oxygen sensors can occasionally trigger a CEL on stock vehicles due to the new advances of technology and would require an O2 spacer to bring the vehicle back to equilibrium and allow the ECU to read exhaust gases within the proper threshold.
FEATURES:
• Fits most makes & models worldwide (Specify Angle option from drop down above and Quantity needed for your specific vehicle)
• Spacer available in a 90 Degree
• Male end threads into existing M18 x 1.5 O2 Bungs
• Spacer body dimensions: 3 3/4" L x 1 1/2" W x 1 1/2" H
• Fitting dimensions: 1" L x 1" W x 1" H (not including threaded portion)
• 1" depth of threads on fittings for adjustments
Read about MotoIQ's 987.2 Cayman S track build that used these O2 Spacers
NOTES:
• For use on DOWNSTREAM oxygen sensors only
Universal fitment for all cars
• For off road competition use only, not to be use on public roads or highways. Please check with your local authorities to ensure compliance with all laws.
• There is no guarantee this will prevent a CEL from triggering, please contact a Fabspeed Performance Specialist for more details.
PURCHASE DISCLAIMER: Fabspeed Motorsport does not condone the use of emission defeat devices for any vehicles used on public streets or roadways. Fabspeed Motorsport will not tamper, remove, disable, or bypass emissions equipment on a motor vehicle in accordance with 40 CFR Section 86.1854.12(a)(3), Clean Air Act 40 CFR 1068.101(b). This includes software, known as tunes, that reprogram a motor vehicles electronic control module to alter engine performance and enable the removal of filters, catalysts, and other critical emissions controls.
Product Information
Fabspeed Universal 45 Degree O2 spacers with catalytic converters, Pair.Product Details:
There is no guarantee this will prevent a CEL from triggering
Universal O2 spacers with real precious metal Catalytic Converters lengthen the distance between the O2 spacer(s). We've taken our spacers a step further by having built-in catalytic converters to allow the ECU to properly read exhaust gas and perform at optimal performance.
Oxygen sensors can occasionally trigger a CEL on stock vehicles due to the new advances of technology and would require an O2 spacer to bring the vehicle back to equilibrium and allow the ECU to read exhaust gases within the proper threshold.
FEATURES:
• Fits most makes & models worldwide (Specify Angle option from drop down above and Quantity needed for your specific vehicle)
• Spacer available in a 90 Degree
• Male end threads into existing M18 x 1.5 O2 Bungs
• Spacer body dimensions: 3 3/4" L x 1 1/2" W x 1 1/2" H
• Fitting dimensions: 1" L x 1" W x 1" H (not including threaded portion)
• 1" depth of threads on fittings for adjustments
Read about MotoIQ's 987.2 Cayman S track build that used these O2 Spacers
NOTES:
• For use on DOWNSTREAM oxygen sensors only
Universal fitment for all cars
• For off road competition use only, not to be use on public roads or highways. Please check with your local authorities to ensure compliance with all laws.
• There is no guarantee this will prevent a CEL from triggering, please contact a Fabspeed Performance Specialist for more details.
PURCHASE DISCLAIMER: Fabspeed Motorsport does not condone the use of emission defeat devices for any vehicles used on public streets or roadways. Fabspeed Motorsport will not tamper, remove, disable, or bypass emissions equipment on a motor vehicle in accordance with 40 CFR Section 86.1854.12(a)(3), Clean Air Act 40 CFR 1068.101(b). This includes software, known as tunes, that reprogram a motor vehicles electronic control module to alter engine performance and enable the removal of filters, catalysts, and other critical emissions controls.
Price: €429.82 inc. VAT
Orderable - 21 to 42 Days
Shop Securely
12 Month Warranty
Worldwide Delivery
