Retro Line

Radio delete cubby pocket.



Fits:
Porsche 911 - 1974 to  1989

When removing the radio, it was impossible to find a replacement cubby that fit perfectly, maximized the space, and looked like it was meant to be there. All aftermarket cubbies were either too thin, poorly fitting, or impossible to mount, and none of them had a well-finished surround trim.

Now offering this radio delete cubby pocket to anyone who wants to utilise the space for more storage instead of using available block-off plates. The pocket is made from PA12 nylon, making it very durable and resistant to heat, chemicals, and wear. The finish texture resembles typical car plastic parts.

Inside dimensions of the pocket:

Width: 177mm / 6.95"
Height: 44mm / 1.73"
Depth: 102mm / 4" (deep enough to hold a phone but not too deep to make it hard to pull items out)

Installation involves sliding the pocket into the opening, then sliding four retaining blocks (three on the bottom, one on the top) from the back of the pocket into the guides. These blocks securely attach the pocket against the metal dash. After the blocks are in place, use a thin needle or nail to align the nuts inside the blocks with the holes in the pocket. Finally, fasten everything with seven screws (this needs to be done inside the pocket, so it’s best to use a Phillips head screwdriver attachment; finger tight should be enough—do not over-tighten).

Included:

• Pocket
• 4 mounting blocks
• 7 screws

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91155246302

The product you are viewing cross references to these numbers

Centre console gauge pod. 



Fits:

Porsche 986 Boxster - 1997 to 2004
Porsche 996 - 1997 to 2005

If you have deleted your center dash or are planning to, but still want to keep or add an auxiliary gauge while maintaining a clean, minimalistic OEM look, this product is for you.

The idea came when considering removing my center dash but hesitated because I didn't want to lose the air/fuel ratio gauge. There was nothing on the market that allowed for adding a gauge once the center dash was removed, so it was decided to create one.

The gauge holder has an open bottom to accommodate various gauge depths. The gauge is held in place by friction, with the diameter of the opening slightly more than 52mm to account for slight variations in gauge diameters between manufacturers. For a snug and secure fit, you can add a bit of tape around the gauge.

This fits Porsche 911 (1999-2005) 996 generation as well as the Boxster 986.

The part is made from highly durable and heat-resistant HP PA 12 nylon. It is dyed black to resemble typical car plastics but can be finished to match your interior.

Please note - Gauge in picture is not included

Storage tray retrofit centre console



Fits:
Porsche 986 Boxster - 1997 to 2004
Porsche 996 - 1997 to 2005 (Coupe models only)

This is a full replacement of the ashtray/window switch panel, transforming it into a double window switch with a larger storage cubby.
Please note: The window switches shown are for demonstration purposes only and are not included. You will need to reuse your existing switches.

The idea behind this upgrade is simple: all coupes (Carrera, turbo, GT2, GT3, etc.) come with a center console panel designed to accommodate four window switches (primarily used in convertibles). As a result, coupe owners end up with two blank dummy buttons in their consoles. No one needs those blanks or an ashtray; what we do need is a place to store small to medium items like a phone.  

The main goal is to maintain a stock appearance. This cubby blends in perfectly, following the curves of the center console to fit seamlessly. You may notice small enhancements such as the angled position of the buttons and a small ridge between them. These features provide more tactile separation between the button switches, making it easier to identify the correct switch without looking. How many times have you or your passenger opened the wrong window? This design aims to prevent that.

Manufactured with PA12 Nylon, this product is strong, durable, and heat resistant.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

99655209500

The product you are viewing cross references to these numbers

Ignition Harness for CDI 3 PIN. 



This is designed to replace your aging and cracked wiring harness that connects the CDI box to the ignition coil and ignition distributor. 

Fits:
Porsche 911 E / S - 1969

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

90161209200

The product you are viewing cross references to these numbers

Cup / drinks holder. Side mount



Fits
Porsche 992 - 2019 Onwards

I'm a fan of the fold out cup holders but if you've had any amount of seat time with a drink in the car then you'll know drinks move and spill on your HVAC buttons. This commonly makes your fan/temp controls sticky and sometimes non responsive. With the 992 911 2020+ interior update some cars have a cup holder in the centre console where a small ashtray or cubby is on all previous 911s and current Caymans. This is a custom made cupholder to utilize un-used space in the car and add an additional convenience to your experience to all other makes and models. Visually the goal is to offer a piece that does not deviate from the OEM look of the car while adding function.

Package Includes: 1x Cup holder. 1x Leather wrapped side brackets. 1x Kup Bracket. Satin Black. Plug and play. 5-15 min install time.

Plug & Play: Minimal to no tools required. Slip the side bracket in. It will slide into place and you will feel it fall into the casting behind the side cover. Screw the Kup brackets together. attach the Kup onto the bracket. 

Note
These are 3d printed parts. There will be support marks and small/minor blemishes on some surfaces. We post treat these as best we can to match the OEM look and feel. The pictures above represent exactly what you should expect.

Suspension dampers kit Front & Rear Safari Style for Porsche 911 1969-89 , this is a "Tarmac" road set up 

Set of 4 Front & Rear.  This kit includes larger 18mm ball joints and lock rings 

Fits:
Porsche 911 1969 to 1989

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

CLP12-1004

The product you are viewing cross references to these numbers

Suspension dampers kit Front & Rear Safari Style for Porsche 911 1969-89 , this is a "Gravel" off road set up 

Set of 4 Front & Rear.  This kit includes larger 18mm ball joints and lock rings 

Fits:
Porsche 911 1969 to 1989

Safari-Style Gravel Suspension Damper Kit (Front & Rear) for Porsche 911 (1969-1989)

Take your Porsche 911 off the beaten path with this high-performance suspension damper kit, designed for "Gravel" off-road setups. This complete kit includes four dampers (front and rear) engineered to deliver exceptional durability, control, and performance on challenging terrains.

Key Features:

Safari-Style Design: Tailored for rugged off-road adventures.

Enhanced Components: Includes robust 18mm ball joints and lock rings for superior strength and longevity.

Precision Fit: Custom-designed to fit Porsche 911 models from 1969 to 1989.

Transform your classic 911 into a gravel-conquering machine with this ultimate suspension upgrade.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

CLP12-1002

The product you are viewing cross references to these numbers

Stone chip guards black set. Porsche 968 Paint protection film
2 parts for front wings 



Fits:
Porsche 968

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

SG968B

The product you are viewing cross references to these numbers

Stone Chip Foil clear - NARROW BODY
Left or right side



Fits:
Porsche 911 1965-89

Retro Line - High quality Aftermarket products made as replacement parts.

Select below please

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

SG911C

The product you are viewing cross references to these numbers

Stone chip foil clear, Turbo body WIDE BODY



Fits:
Porsche 930 Turbo 1977-89
Porsche 911 Widebody 1974-89

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

SG930C

The product you are viewing cross references to these numbers

Stone chip guards clear set. Porsche 968 Paint protection film
2 parts for front wings 



Fits:
Porsche 968

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

SG968C

The product you are viewing cross references to these numbers

Stone guard film SET OF 2 for rear doors Black. Porsche Macan

Fits:
Porsche 95B Macan 2014-18
I6EA - for cars without additional body covers, side stone guards
I6ET - stone guard film, poor road package

Click 'Zoom in' for large parts diagram.
Diagram ref no 15

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

SG946B

The product you are viewing cross references to these numbers

Stone guard film SET OF 2 for rear doors Clear. Porsche Macan

Fits:
Porsche 95B Macan 2014-18
I6EA - for cars without additional body covers, side stone guards
I6ET - stone guard film, poor road package

Click 'Zoom in' for large parts diagram.
Diagram ref no 15

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

SG946C

The product you are viewing cross references to these numbers

Stone chip guard rear, Set of 2 BLACK longer version. Porsche 970 Panamera 



Fits:
Porsche 970 Panamera 2010-16

Click 'Zoom in' for large parts diagram.
Diagram ref no 9

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

SG970B

The product you are viewing cross references to these numbers

Stone chip guard set - clear. Porsche 997 Turbo / C4/ C4S

Fits to lower rear 1/4 panels



Fits - Wide Body Cars
Porsche Porsche 997 Turbo / C4/ C4S

2 Parts
Left & Right

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

SG997TC

The product you are viewing cross references to these numbers

Stone chip guard set - black. Porsche 997 Turbo / C4/ C4S

Fits to lower rear 1/4 panels



Fits - Wide Body Cars
Porsche 997 Turbo / C4/ C4S

2 Parts
Left & Right - Textured black

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

SG997TB

The product you are viewing cross references to these numbers