Retro Line

Engine wiring harness loom.

Fits:
Porsche 964 Carrera 2 Tiptronic - 1991 to 1994
Engine code M64.02

Complete engine harness for the 964 Carrera Tiptronic.

Please note that the chassis part and cover from the 12 pole male are no longer available new and need to be re-used from your original harness (2 min job instructions included)

Special order made to order parts please allow 2 – 4 weeks

Diagram ref no 1

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

96460701602

The product you are viewing cross references to these numbers

Engine wiring harness loom.



Fits:
Porsche 964 Carrera 4 - 1989 to 1990
Engine code M64.01

Complete engine harness for the 964 1989 -1990 Carrera 4

Please note that the chassis part and cover from the 12 pole male are no longer available new and need to be re-used from your original harness (2 min job instructions included)

Special order made to order parts please allow 2 – 4 weeks

Click 'Zoom in' for large parts diagram.
Diagram ref no 1

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

96460701601

The product you are viewing cross references to these numbers

DME wiring harness.



Fits:
Porsche 964 Carrera 2 tiptronic (M249) up to 1991

DME harness for 964 Complete harness with 55PIN ECU/DME connector to Motronic Box


Connectors for:

• T16
• Version coding
• Coding plug
• Oxygen sensor
• Pressure sensor
• Air flow sensor
• Throttle valve switch
• Idle speed sensor
• Resonance plate
• Tank vent valve
• Knock sensor 1
• Knock sensor 2
• NTC temp sensor
• Speed sender
• Ignition coil 1
• Ignition coil 2
• Ignition control unit 1
• Ignition control unit 2
• T31 connection
• Timing belt switch
• Hall sender

Special order made to order parts please allow 2 – 4 weeks

Comes with detailed connection diagram.

Loom is made to order

Click 'Zoom in' for large parts diagram.
Diagram ref no 2

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

96461217303

The product you are viewing cross references to these numbers

Stone Chip Guards Set Black Porsche Boxster 986 / 987 Boxster / Cayman



Fits to lower rear 1/4 panels

Fits
Porsche 986 Boxster
Porsche 987 Boxster / Cayman

2 parts
Left & Right - Textured black

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

SG986B

The product you are viewing cross references to these numbers

Stone chip guard set - clear. Porsche 996 turbo

Fits to lower rear 1/4 panels



Fits - Wide Body Cars
Porsche 996 turbo

2 Parts
Left & Right

Stone chip guard set - Black. Porsche 996 Turbo

Fits to lower rear 1/4 panels



Fits - Wide Body Cars
Porsche 996 turbo

2 Parts
Left & Right - Textured black

Stone chip guard set - clear. Porsche 996 Carrera 4S

Fits to lower rear 1/4 panels



Fits - Wide Body Cars
Porsche 996 Carrera 4S

2 Parts
Left & Right

Stone chip guard set - black. Porsche 996 Carrera 4S

Fits to lower rear 1/4 panels



Fits - Wide Body Cars
Porsche 996 Carrera 4S

2 Parts
Left & Right - Textured black

Stone chip guard set - clear. Porsche 996 Carrera / Carrera 4

Fits to lower rear 1/4 panels



Fits - Narrow Body Cars
Porsche 996 Carrera
Porsche 996 Carrera 4

2 Parts
Left & Right

Stone chip guard set - black. Porsche 996 Carrera / Carrera 4

Fits to lower rear 1/4 panels



Fits - Narrow Body Cars
Porsche 996 Carrera
Porsche 996 Carrera 4

2 Parts
Left & Right - Textured black

Cup / drinks holder. Side mount



Fits
Fits 718 Boxster, 718 Cayman, 718 Spyder, 911, Boxster, Cayman.

** Any Porsche with this centre console design will fit ** (some may be missing from below, I will update as best I can)

Porsche 991 ALL
Porsche 718 ALL
Porsche 981 ALL
Porsche 911 ALL 2011+
Porsche Boxster ALL 2013+
Porsche Cayman ALL 2014+

I'm a fan of the fold out cup holders but if you've had any amount of seat time with a drink in the car then you'll know drinks move and spill on your HVAC buttons. This commonly makes your fan/temp controls sticky and sometimes non responsive. With the 992 911 2020+ interior update some cars have a cup holder in the centre console where a small ashtray or cubby is on all previous 911s and current Caymans. This is a custom made cupholder to utilize un-used space in the car and add an additional convenience to your experience to all other makes and models. Visually the goal is to offer a piece that does not deviate from the OEM look of the car while adding function.

Package Includes: 1x Cup holder. 1x Side Bracket. 1x Cup Bracket. Satin Black. Plug and play. 5-15 min install time.

Fitment: 2011 - 2022 all two door Porsche cars with the ashtray/cubby in front of the armrest. YETI, Blender bottles, and larger size tumblers fit great.

Plug & Play: Minimal to no tools required. Pull on the centre console passenger side cover. Slip the side bracket in. It will slide into place and you will feel it lock into the casting behind the side cover. Screw the cup bracket into the side bracket. Slide cup onto the bracket.




Note
These are 3d printed parts. There will be support marks and small/minor blemishes on some surfaces. We post treat these as best we can to match the OEM look and feel. The pictures above represent exactly what you should expect.

LCD display in MPH replacement for Porsche 964 / 993 instrument clusters



This LCD panel fits in to the Rev counter for cars with M659 on-board COMPUTER the LCD panel this should only be fitted by a professional

Fits:
Porsche 964 1989-94
Porsche 993 1994-98

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

993641312XX

The product you are viewing cross references to these numbers

Centre console cup / drinks holder. Low Profile Edition



Fits
Porsche 991.1 - All
Porsche 991.2 - All
Porsche 981 Boxster - All
Porsche 981 Cayman - All
Porsche 718 Boxster - All
Porsche 718 Cayman - All

Available Versions
• Standard Edition
• Low Profile Edition
• Phone Holder Edition - Additional slot is added to fit your phone

If you've had any amount of seat time with a drink in the car then you'll know drinks move and spill on your HVAC buttons.
This commonly makes your fan/temp controls sticky and sometimes non responsive. With the 992 911 2020+ interior update some cars have a cup holder in the centre console where a small ashtray or cubby is on all previous 911s and current Caymans.

This is a custom made cup holder to mimic the location of the 992 ones to add additional convenience
Visually the goal is to offer a piece that does not deviate from the OEM look of the car while adding function.

Package Includes: 1x Cup holder. Satin Black (Matching black to centre console)

Plug and play. 5 min install time

Fitment:
2011 - 2022 all two door Porsche cars with the ashtray/cubby in front of the armrest. 2 3/4 Cup size. This is going to fit everything the slide out cup holder could. Additionally, with this design you can add on a "Cup holder extender" that will sit higher and larger to fit your YETI, Blender bottles, and larger size tumblers should you like.

Plug & Play:
No tools required. Remove trim ring by pulling up. Remove button cluster by pulling up. Slide OEM ashtray forward and up. Install your new cup holder. Re-install the cluster and trim ring.

Direct replacement for Part Number: 99155314300A05
Supersession(s): 991-553-143-00-A05

Some 911's have a cigarette/charger port in the ashtray area (Smokers Package). This cup holder will fit the same. The charging port can be relocated or deleted.

Note
These are 3d printed parts. There will be support marks and small/minor blemishes on some surfaces. We post treat these as best we can to match the OEM look and feel. The pictures above represent exactly what you should expect.

Centre console cup / drinks holder. Phone Holder Edition - Additional slot is added to fit your phone



Fits
Porsche 991.1 - All
Porsche 991.2 - All
Porsche 981 Boxster - All
Porsche 981 Cayman - All
Porsche 718 Boxster - All
Porsche 718 Cayman - All

Available Versions
• Standard Edition
• Low Profile Edition
• Phone Holder Edition - Additional slot is added to fit your phone

If you've had any amount of seat time with a drink in the car then you'll know drinks move and spill on your HVAC buttons.
This commonly makes your fan/temp controls sticky and sometimes non responsive. With the 992 911 2020+ interior update some cars have a cup holder in the centre console where a small ashtray or cubby is on all previous 911s and current Caymans.

This is a custom made cup holder to mimic the location of the 992 ones to add additional convenience
Visually the goal is to offer a piece that does not deviate from the OEM look of the car while adding function.

Package Includes: 1x Cup holder. Satin Black (Matching black to centre console)

Plug and play. 5 min install time

Fitment:
2011 - 2022 all two door Porsche cars with the ashtray/cubby in front of the armrest. 2 3/4 Cup size. This is going to fit everything the slide out cup holder could. Additionally, with this design you can add on a "Cup holder extender" that will sit higher and larger to fit your YETI, Blender bottles, and larger size tumblers should you like.

Plug & Play:
No tools required. Remove trim ring by pulling up. Remove button cluster by pulling up. Slide OEM ashtray forward and up. Install your new cup holder. Re-install the cluster and trim ring.

Direct replacement for Part Number: 99155314300A05
Supersession(s): 991-553-143-00-A05

Some 911's have a cigarette/charger port in the ashtray area (Smokers Package). This cup holder will fit the same. The charging port can be relocated or deleted.

Note
These are 3d printed parts. There will be support marks and small/minor blemishes on some surfaces. We post treat these as best we can to match the OEM look and feel. The pictures above represent exactly what you should expect.

Centre console cup / drinks holder, Standard Edition



Fits
Porsche 991.1 - All
Porsche 991.2 - All
Porsche 981 Boxster - All
Porsche 981 Cayman - All
Porsche 718 Boxster - All
Porsche 718 Cayman - All

Available Versions
• Standard Edition
• Low Profile Edition
• Phone Holder Edition - Additional slot is added to fit your phone

If you've had any amount of seat time with a drink in the car then you'll know drinks move and spill on your HVAC buttons.
This commonly makes your fan/temp controls sticky and sometimes non responsive. With the 992 911 2020+ interior update some cars have a cup holder in the centre console where a small ashtray or cubby is on all previous 911s and current Caymans.

This is a custom made cup holder to mimic the location of the 992 ones to add additional convenience
Visually the goal is to offer a piece that does not deviate from the OEM look of the car while adding function.

Package Includes: 1x Cup holder. Satin Black (Matching black to centre console)

Plug and play. 5 min install time

Fitment:
2011 - 2022 all two door Porsche cars with the ashtray/cubby in front of the armrest. 2 3/4 Cup size. This is going to fit everything the slide out cup holder could. Additionally, with this design you can add on a "Cup holder extender" that will sit higher and larger to fit your YETI, Blender bottles, and larger size tumblers should you like.

Plug & Play:
No tools required. Remove trim ring by pulling up. Remove button cluster by pulling up. Slide OEM ashtray forward and up. Install your new cup holder. Re-install the cluster and trim ring.

Direct replacement for Part Number: 99155314300A05
Supersession(s): 991-553-143-00-A05

Some 911's have a cigarette/charger port in the ashtray area (Smokers Package). This cup holder will fit the same. The charging port can be relocated or deleted.

Note
These are 3d printed parts. There will be support marks and small/minor blemishes on some surfaces. We post treat these as best we can to match the OEM look and feel. The pictures above represent exactly what you should expect.

Fully prepared 911 1970-1973 front harness with 2 x 6 pole male connector and relay base (for horn).

Fits:
Porsche 911 1971 - 1973

•   Waxed lacing wire and each wire at the right length.
•   Runs from fuse box to left and right fender / washer pump.
•   Original colour coded wiring.
•   Harness will exactly fit like the original.
•   Wire tube, and oil resistant tape as original.
•   Terminals have rubber sleeves.
•   New 6 pole male connectors and relay socket included.

Diagram ref no 3

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91161200310

The product you are viewing cross references to these numbers