Kits

IGNITION KIT. Includes Ignition Leads, Rotor Arm & Distributor Cap.



Ignition Lead Set
Rotor Arm
Distributor Cap

Fits:
Porsche 911SC 3.0L 1978-83
188Bhp & 204Bhp cars
Porsche 930 Turbo

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

IGNITIONKIT911.1

The product you are viewing cross references to these numbers

IGNITION KIT. Includes Ignition Leads, Rotor Arm & Distributor Cap.

Ignition Tune-Up Kit for Your 911 3.2L, Restore power and performance to your 911 3.2L with this complete ignition tune-up kit. The kit includes a distributor cap, distributor rotor, and a full set of spark plug wires with ignition coil lead wires, providing everything needed for a comprehensive ignition service.

Fits:
Porsche 911 1984-1986 3.2L  (Not 1984 cars)

Porsche 911 1987-1989 3.2L G50

Ignition Tune-Up Kit

An ignition tune-up kit includes all the parts you need to service your vehicle's ignition system. Components like spark plugs, ignition coils, spark plug connectors, and spark plug wires will eventually require replacement.

When these components are used past their useable service life you will often experience a vehicle that does not run smoothly, suffers from misfires, or even completely dead cylinders due to no spark. Replacing ignition components should be done on a regular interval

Ignition Tune-Up Kit Failure Symptoms

• Check engine light due to misfire 
•  P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308 and other cylinder specific misfire OBD fault codes 
•  Hesitation while accelerating 
•  Poor fuel economy due to incomplete combustion       

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

IGNITIONKIT911.2

The product you are viewing cross references to these numbers

Aluminum Intake Plenum Competition + Throttle Body Kit. Porsche 987 Cayman/Boxster S 3.4L DFI IPD



The IPD 987.2 Boxster "Competition" Plenum was designed to meet the needs of the most demanding Boxster S enthusiasts. The "Competition" Plenums is internally larger and specifically designed to utilized the larger 82mm 997 GT3 throttle body. This new 987.2 Competition Plenum follows in the foot steps of the very successful 987.1 Competition Plenum, which has proven itself to be the absolute single best performance mod that can be installed on any 987.1. The combination of the patented IPD "Y" designed Plenum and Porsche's largest TB yield great performance gains that can be seen and felt throughout the entire power band.

The "Competition" version was designed and developed to work with Boxster S's equipped with high quality high-flow aftermarket cat-back exhausts. The addition of headers and high-flow cats will only further compliment the dramatic increases with intake air flow delivered by the IPD Plenum.

Performance gains take place throughout both horsepower and torque curves but are most realized through the mid-range and well into peak power range. This system develops up to 20+ HP on Boxster already equipped with aftermarket cat-back exhausts. Once installed, the 987.2 Boxster Competition Plenum will truly transform your Porsche Boxster driving experience.

Fits:
Porsche 987 GEN2 Cayman S 3.4L DFI
Porsche 987 GEN2 Boxster S 3.4L DFI

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

IPDKIT98734

The product you are viewing cross references to these numbers

Aluminum Intake Plenum Competition + 74mm Throttle Body Porsche 986 Boxster IPD



The 986 Boxster marked Porsche's return to a purpose built 2 seat roadster since the famed 550 Spyder. This liberating open cockpit platform was instrumental in saving Porsche from financial uncertainty and was Porsche highest volume seller from 1997 to 2003, until the Cayenne entered the Porsche line up.

The perfectly balanced mid engine 986 Boxster was designed to deliver driving excitement on sinuous back country roads while enabling the driver (and passenger) to literally take in the sights, sun and smells of the surrounding environment and listening to the intoxicating mechanical sounds of a flat 6 Boxer engine tones.

The Boxster experience can only be further heightened by adding improved performance. The IPD Plenums provide impressive the power gains throughout the entire power band making for an even more visceral Porsche driving experience.

All 986 Boxster IPD Plenum applications are designed to utilize the larger 74mm Porsche throttle body. The combination of the patented "Y" design of the IPD Plenum combined with a larger TB allow for improved air flow and intake air speed. The IPD Plenum is the absolute single best performance mod you can install on a Porsche Boxster, providing impressive power gains throughout the entire power band, especially in the midrange where we enjoy it most.

Installation of the 986 Boxster IPD Plenums comes with additional hardware and is relatively straight forward although IPD strongly recommend installation be performed by a trained Porsche technician.

The 74mm Boxster IPD Plenum and upgraded 74mm (from 68mm) throttle body package is recommended for Boxster enthusiasts looking for considerable performance gains. Performance gains can be felt throughout the entire power band making the Boxster driving experience even more visceral.

The IPD Boxster Plenum will provide the most impressive power gains of any engine upgrade available and will truly transform your Boxster driving experience. The 74mm IPD Plenum is the best Boxster modification on the market and will further compliment other mods such as exhaust, software and beyond.

Fits:
Porsche 986 Boxster S 3.2L 2000-04
Porsche 986 Boxster 2.7L 2000-04

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

IPDKIT98632

The product you are viewing cross references to these numbers

Aluminum Intake Plenum Competition + 82mm Throttle Body Porsche 987 Cayman/Boxster S 3.4L IPD



Fits:
Porsche 987 GEN1 Cayman S 3.4L
Porsche 987 GEN1 Boxster S 3.4L

987 Competition Cayman 3.4L Plenum: HP Gains 20+ / Torque Gains 18 Requires upgrading factory 74mm Throttle Body with 997 GT3 82mm Throttle Body

Recommended to be installed on modified Caymans with Hi-Flow Cat back exhaust

The perfectly balanced mid engine Cayman/Boxster is Germany's canyon carving track meister. Unfortunately, the Cayman/Boxster was delivered slightly under powered from the factory so as not to threaten the Carrera's thrown. The Cayman IPD intake plenum delivers increased performance that puts the Cayman/Boxster in the ring with the Carrera.

The IPD Plenum out performs every other intake system on the market. Don't be fooled by other competitors claiming to offer Plenums. All factory Porsche air distributors are of the "T" variety and therefore suffer from less than ideal air flow and intake air speed.

The genius and power behind the IPD plenums comes from the patented "Y" style design and optimized diversion areas to deliver real and impressive power that will transform your Cayman's/Boxster's performance and heighten your Porsche driving experience.

The Cayman/Boxster IPD Intake Plenums are available in 3 versions, each one specifically designed to meet the performance requirements of varying Cayman/Boxster enthusiasts. IPD offers the ultimate Cayman/Boxster performance upgrades, all the way from mild to wild.

The IPD Cayman/Boxster "Competition" Plenum was designed to meet the needs of the most demanding Cayman/Boxster S enthusiasts. The "Competition" Plenums is even larger and utilizes the 997 GT3 82mm throttle body allowing it to deliver even greater air flow and substantial increases in performance.

The "Competition" version is designed to work with both bone stock Caymans/Boxsters but produces even more horsepower gains (20+) with Caymans/Boxsters already equipped with after market "cat back" high flow performance exhaust and other performance mods.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

IPDKIT98732

The product you are viewing cross references to these numbers

Ignition Kit Distributor Caps + Rotor Arms.


2 x Distributor Caps


2 x Rotor Arms

Fits:
Porsche 964 1989-94
Porsche 993 09/1989 - 08/1997

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

IGNITIONKIT998

The product you are viewing cross references to these numbers

Headlamps Clear for RHD cars.
For cars WITH washer jet
SET OF 2



Upgrade from the old style amber headlamps to the more modern clear type.

Price includes:
- 2 Halogen headlamps
- 2 infill corners.

Fits:
Porsche Boxster 986 1997-04
Porsche 996 1997-08/01 (non headlamp leveling)

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

LIGHTKIT03W

The product you are viewing cross references to these numbers

Aluminum Intake Plenum "Competition" + Y-Pipe + 82mm Throttle Body Porsche 997 Turbo IPD



The incredible 997 Porsche Turbo is the most revolutionary and capable Porsche Turbo to ever come out of Germany. The already explosive power can be further increased with the new 997 Turbo IPD Intake Plenums.

The patented IPD Plenum design works exceptionally well with all forced induction applications and the 997 Turbo is no exception. Power and torque increases provided by the IPD plenum are impressive and stay over and above all factory power curves from launch to redline. Maximum power increases take place in the midrange where it's most needed and most critical.

Maximum horsepower gains range from 30 to 35 depending on vehicle condition and pre-existing mods. The 997 Turbo plenums deliver smooth and linear power with considerably quicker boost response creating a longer and more desirable power band. The Turbo plenums deliver reliable performance for both street and motorsport applications enhancing the already visceral Porsche Turbo driving experience.

Unlike the 996 Turbo the 997 Turbo requires an "adaptation" period that can be fully realized with either a series of hard pulls on the dyno or 10 to 50 miles of hard driving which of course IPD recommends only be performed on a closed circuit race track.

The 997 Turbo has an extremely sensitive ECU/DME making it prone to external environmental corrections so it is imperative that proper, adequate and consistent cooling be available when you dyno any of the 997 Turbos to get accurate and reliable dyno figures both before and after each test.

Installation of all Turbo Plenums is highly recommended to be performed by qualified and trained Porsche technicians.

Power obsessed Turbo customers looking to push the motorsport envelope a little harder would best benefit from the larger 82mm "Competition" IPD plenum fitted with a factory 997 GT3 82mm Porsche throttle body (additional purchase required).

The larger 82mm intake opening allows for even greater air flow to help optimize the more extreme mods such as larger turbos, intercoolers, Y Pipes and more aggressive software.

This larger version Plenum is also designed to perform with the higher flowing IPD "Y" Pipe.

997.1 Turbo Competition Plenum: HP Gains 30-35 / Torque Gains 35-40. Requires upgrading factory 74mm TB with 997 GT3 82mm Thottle Body

Fits:
Porsche 997 Turbo

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

IPDKIT997TT1

The product you are viewing cross references to these numbers

Aluminum Intake Plenum "Competition" 82MM + Throttle Body Porsche 997 Turbo IPD



The incredible 997 Porsche Turbo is the most revolutionary and capable Porsche Turbo to ever come out of Germany. The already explosive power can be further increased with the new 997 Turbo IPD Intake Plenums.

The patented IPD Plenum design works exceptionally well with all forced induction applications and the 997 Turbo is no exception. Power and torque increases provided by the IPD plenum are impressive and stay over and above all factory power curves from launch to redline. Maximum power increases take place in the midrange where it's most needed and most critical.

Maximum horsepower gains range from 30 to 35 depending on vehicle condition and pre-existing mods. The 997 Turbo plenums deliver smooth and linear power with considerably quicker boost response creating a longer and more desirable power band. The Turbo plenums deliver reliable performance for both street and motorsport applications enhancing the already visceral Porsche Turbo driving experience.

Unlike the 996 Turbo the 997 Turbo requires an "adaptation" period that can be fully realized with either a series of hard pulls on the dyno or 10 to 50 miles of hard driving which of course IPD recommends only be performed on a closed circuit race track.

The 997 Turbo has an extremely sensitive ECU/DME making it prone to external environmental corrections so it is imperative that proper, adequate and consistent cooling be available when you dyno any of the 997 Turbos to get accurate and reliable dyno figures both before and after each test.

Installation of all Turbo Plenums is highly recommended to be performed by qualified and trained Porsche technicians.

Power obsessed Turbo customers looking to push the motorsport envelope a little harder would best benefit from the larger 82mm "Competition" IPD plenum fitted with a factory 997 GT3 82mm Porsche throttle body (additional purchase required).

The larger 82mm intake opening allows for even greater air flow to help optimize the more extreme mods such as larger turbos, intercoolers, Y Pipes and more aggressive software.

This larger version Plenum is also designed to perform with the higher flowing IPD "Y" Pipe.

997.1 Turbo Competition Plenum: HP Gains 30-35 / Torque Gains 35-40. Requires upgrading factory 74mm TB with 997 GT3 82mm Throttle Body

Fits:
Porsche 997 Turbo

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

IPDKIT997TT

The product you are viewing cross references to these numbers

Aluminum Intake Plenum "Competition" 82MM + Throttle Body.



Porsche has been controlling engine output by restricting the inlet track for decades. This has been successfully accomplished by utilizing smaller throttle bodies. This simple power control solution has been a very effective way of preventing lower level models from out performing certain flagship models, especially models with prolific racing pedigree. Although the factory engine packages are fantastic performance machines, they are engineered and developed to achieve specific performance numbers that satisfy a target demographic and compete with rival brands. Unfortunately driving enthusiasts who seek an elevated Porsche driving experience require performance levels well outside the target market.

All of the IPD Plenums deliver substantial power and torque gains, but when combined with larger throttle bodies they perform even better. All of the IPD "Competition" Plenums utilize the next largest size throttle body offered by Porsche. In this case, the Competition Carrera upgrades the factory OE 74mm throttle body with Porsche's 82mm 997 GT3 throttle body. All of our Competition Plenums are designed to perform with cars equipped with high performance exhaust systems. The more extensive the exhaust system (headers, kats and mufflers) the better. Optimizing air intake and exhaust together creates a balanced performance package that allows the engine to inhale and exhale more air thus creating more power and torque.

IPD has pioneered another new Plenum design with the Competition Carrera Plenum. Laminar flows and volumetric efficiencies have been further enhanced with our unique and innovative internal merge collector area. This completely new approach has yielded not only great performance gains but more linear power delivery and improved throttle response as well. Gains vary depending on pre-existing mods and quality of after-market exhaust installed. As we all "should" know, horsepower and torque become harder to find and typically more expensive as we climb the proverbial performance ladder. That being said, performance components yield different power gains depending on the order they were installed. IPD tests and evaluates all products on bone stock cars, this establishes a level playing field and a better "apples to apples" comparison. The Competition Carrera Plenum however is designed to work with applications that are already moderately to heavily modified. Power gains will vary with each Carrera, but the bottom line is, there will be noticeable and impressive gains that are sure to make any Porsche Carrera driving enthusiast smile.

Power improvements will be fully realized once the factory ECU/DME makes all the necessary "adaptation" requirements. This process can be expedited with a series of "hard pulls" or spirited full throttle acceleration runs through the gears. Of course this should only be performed on a closed course circuit.

Requires upgrading factory 74mm TB with 997 GT3 82mm Thottle Body

Fits:
Porsche 997 3.8L S
Porsche 997 3.6L

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

IPDKIT99701

The product you are viewing cross references to these numbers

Aluminum Intake Plenum "Competition" 82MM + Throttle Body Porsche 996 Carrera 3.4L /3.6L IPD



Fits:
Porsche Porsche 996 Carrera C2 3.6L
Porsche Porsche 996 Carrera C4 3.6L
Porsche Porsche 996 Carrera C2 3.4L*
Porsche Porsche 996 Carrera C4 3.4L*
(*FOR CARS WITH "ELECTRONIC ACCELERATOR (M620)" NOT FOR EARLY CABLE THROTTLE CARS)

Porsche has been controlling engine output by restricting the inlet track for decades. This has been successfully accomplished by utilizing smaller throttle bodies. This simple power control solution has been a very effective way of preventing lower level models from out performing certain flagship models, especially models with prolific racing pedigree. Although the factory engine packages are fantastic performance machines, they are engineered and developed to achieve specific performance numbers that satisfy a target demographic and compete with rival brands. Unfortunately driving enthusiasts who seek an elevated Porsche driving experience require performance levels well outside the target market.

All of the IPD Plenums deliver substantial power and torque gains, but when combined with larger throttle bodies they perform even better. All of the IPD "Competition" Plenums utilize the next largest size throttle body offered by Porsche. In this case, the Competition Carrera upgrades the factory OE 74mm throttle body with Porsche's 82mm 997 GT3 throttle body. All of our Competition Plenums are designed to perform with cars equipped with high performance exhaust systems. The more extensive the exhaust system (headers, kats and mufflers) the better. Optimizing air intake and exhaust together creates a balanced performance package that allows the engine to inhale and exhale more air thus creating more power and torque.

IPD has pioneered another new Plenum design with the Competition Carrera Plenum. Laminar flows and volumetric efficiencies have been further enhanced with our unique and innovative internal merge collector area. This completely new approach has yielded not only great performance gains but more linear power delivery and improved throttle response as well. Gains vary depending on pre-existing mods and quality of after-market exhaust installed. As we all "should" know, horsepower and torque become harder to find and typically more expensive as we climb the proverbial performance ladder. That being said, performance components yield different power gains depending on the order they were installed. IPD tests and evaluates all products on bone stock cars, this establishes a level playing field and a better "apples to apples" comparison. The Competition Carrera Plenum however is designed to work with applications that are already moderately to heavily modified. Power gains will vary with each Carrera, but the bottom line is, there will be noticeable and impressive gains that are sure to make any Porsche Carrera driving enthusiast smile.

Power improvements will be fully realized once the factory ECU/DME makes all the necessary "adaptation" requirements. This process can be expedited with a series of "hard pulls" or spirited full throttle acceleration runs through the gears. Of course this should only be performed on a closed course circuit.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

IPDKIT99601

The product you are viewing cross references to these numbers

Aluminum Intake Plenum Competition + Throttle Body Kit Porsche 996 Turbo/S/X50/GT2



The all mighty 996 Turbo may be the perfect Porsche of them all to benefit from the IPD Plenum. Horsepower and torque gains are substantial and immediate (no adaptation required).

Horsepower improvements range from 30 to 35 and boost response improves considerably making for longer, stronger and of course more pleasurable power curves. The IPD plenum develops horsepower throughout the entire power band, especially where it's needed most, from mid range to top end.

Installation of the 996 Turbo Plenum is very challenging and installation should only be performed by a seasoned and qualified Porsche technician.

The 996 Turbo 74mm "Competition" Plenum is designed to function with more seriously modified Turbos developing over 600+ horsepower. Although this 74mm application has been used with great success on a variety of Turbos ranging from mildly modified to 1000+ HP.

This application requires the larger 74mm Porsche throttle body (additional purchase required) and comes with additional hardware to complete the kit. This "Competition Turbo" Plenum will help modified 996 Turbos realize maximum performance.


The increased air flow and air speed develop by the larger Plenum is designed to work with larger turbos, intercoolers, intake piping, high flow Y Pipes and more aggressive software.

Horsepower gains start around 35 hp and deliver max power slightly higher in the rev range creating better top end performance without the drop in power experienced with the factory air distributor.

996 Turbo Competition Plenum: HP Gains 24 / Torque Gains 26.

Fits:
Porsche 996 Turbo/S/X50/ GT2

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

IPDKIT996TT

The product you are viewing cross references to these numbers

Exhaust muffler / silencer replacement OE Porsche 996 Gen2 (SET OF 2)



Standard specifications exhaust

Standard Replacement exhaust back boxes set of 2 left & right, not for cars fitted with factory sports exhaust.

Fits:
Porsche 996 C2 / C4 / C4S 3.6L 2002-2005
Fits Tiptonic & Manual

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

EXHAUSTKIT72

The product you are viewing cross references to these numbers

The most economical way to change your brake pads & brake disc is to buy our packages.




Porsche 981 Boxster 2.7L (REAR)
Porsche 981 Cayman 2.7L (REAR)

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

BRAKEKIT981.R.BRE

The product you are viewing cross references to these numbers

The most economical way to change your brake pads & brake disc is to buy our packages.




Porsche 981 Boxster S (REAR)
Porsche 981 Cayman S (REAR)

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

BRAKEKIT981S.R.BRE

The product you are viewing cross references to these numbers

Powerflex Black series Front wishbone repair kit and upgrade for Both Left and Right wisebones. This will cover both front wishbones.



Fits:
Porsche 964 1989-94
Porsche 993 1994-98


Powerflex Black Series - Designed for the Track - Ready to Race - Engineered to be the best.

Powerflex Black Series bushes are manufactured using a 95 Shore A compound to provide maximum control of chassis geometry. This compound can be up to 80% more resistant to load than standard rubber and 25% stiffer than our purple performance material.

If your requirements are purely for the ultimate in handling and chassis performance then Powerflex Black Series are unique, offering the most precise and accurate alignment for your chassis.

Replacing your car rubber suspension bushes with Polyurethane Suspension Bushes will give you:

- Better road holding
- Constant steering geometry
- Increased tyre life
- More responsitive steering
- Longer service life of suspension components

Fits to No 12 on the diagram.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

PUBUSHKIT6

The product you are viewing cross references to these numbers