Elephant Racing

Bump steer correcting tie rod kit.
Bump geometry correction. 1 kit, req'd per car.



For Porsche 964 1989-94 W/O RS Wheel Carriers

Lowered cars with non-RS wheel carriers suffer from bump steer and will benefit from bump geometry correction.

Bump steer is a change in toe due to vertical movement of the wheel, such as when driving over a bump. The toe change causes the car to turn, and the driver needs to constantly correct for this to maintain a steady trajectory. This makes the car a handful to drive, especially over bumpy road surfaces.

Bump correction is achieved by moving the tie rod end pivot about 10mm closer to the steering knuckle as compared to the stock tie rod end. This changes the angle of the tie rod to produce the bump geometry correction.

No Need To Convert Wheel Carriers

This Bump Steer Correcting Tie Rod kit provides bump geometry correction with the standard C2/C4 wheel carriers. It is not necessary to convert the wheel carriers to RS type to correct for bump steer when using our kit.

• Corrects for bump steer


• Eliminates rubber inner-joint


• Enhanced driving precision


• Easier and more cost effective than RS wheel carrier conversion

These Elephant Racing bump steer tie rods also eliminate the compliant rubber inner-joint found in the factory 964 tie rods with a spherical bearing providing a more direct and responsive steering feel. Thus, proper suspension geometry is restored, driver corrections are minimized, and vehicle trajectory is stabilized making driving control easier while reducing driver fatigue.

Out Performs All Other Tie Rods

Even on cars fresh from the Porsche factory assembly lines our anti-bump steer kit will reduce bump steer through the full range of motion.



Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

2180031

The product you are viewing cross references to these numbers

Complete oil cooler kit. Contents :



1. HIGH CLEARANCE, UNIVERSAL CROSSOVER PLUMBING KIT

   Kit contents:
    1x Set high-clearance oil lines
    1x Universal crossover pipe
    1x Thermostat
    1x Oil line mounting kit
    1x Finned oil line set
    1x 30mm case fitting 65-71 only

A complete plumbing kit. Enhances tire clearance by routing oil lines above the rear wheel. Universal crossover pipe fits all clutches and all heat exchangers, does not fit G50 transaxle. Includes finned oil lines for added heat dissipation.
This is everything need t connect the oil tank and engine to the front wheel well.


2. SINGLE FENDER COOLER KIT

   Kit contents:
    1x Widemouth Carrera cooler
    1x Cooler mounting kit
    1x Pair oil hoses to hard lines
    1x Stone guard kit

A basic fender mount single-cooler system similar to those equipped on 84-89 911 3.2 carreras.

For Fender Mount Carrera Cooler - Installation Instructions  CLICK HERE

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

0220000_0200011

The product you are viewing cross references to these numbers

Rear swaybar mount kit.



Fits:
Porsche 911/912/930 1965-89

Stock 911 rear swaybar mounts have a nasty habit of tearing away from the body. Stiff sway bars and aggressive driving only accelerate the inevitable mount failure.
Replace your mounts with these super strong aftermarket mounts and solve the problem for good. Requires grinding off the factory mounts and welding for installation.

The mounts have two sets of screw holes to fit both the 66mm bolt spacing as equipped on the 1978 to 1989 cars as well as the 56mm bolt spacing as equipped on the 1965 to 1977 cars.

• Fully machined surfaces for a precision fit
• Consistent material thickness for easy installation
• Tighter tolerances, more surface area, and stronger than any other rear swaybar mounts available.

Click 'Zoom in' for large parts diagram.
Diagram ref no 16

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

91150198300

The product you are viewing cross references to these numbers

Plated & Plugged Hollow Torsion Bars. - REAR
Plated/Plugged 27mm, PAIR



Fits:
Porsche 911/912/930 1965-86
Porsche 356 A / 356 B / 356 Pre-A, C And CS Read Notes* (1948-65)

Our Plated & Plugged Hollow torsion bars are the best available. The ends are plugged to prevent moisture entry that rots ordinary hollow bars from the inside out. The entire bar is zinc plated for superior protection.

Excellent quality control means proper spline fit and spring-rate consistency bar-to-bar. Inferior quality competing bars fail on all counts.

• Hollow, light weight
• Plated & Plugged
• Consistent spring rate
• Great spline fit

Upgrade Hollow bars provide a nice weight savings over equivalent spring rate solid bars, especially true of the heavier rear bars. This is a great way to trim extra pounds from the back of your car.

* The size given is a solid-bar-equivalent. Actual hollow bar measures about. 5mm larger.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

1-PP911R27

The product you are viewing cross references to these numbers

Front control A arm rubber bushing kit. 1 kit required per car.
DIY Bushings Kit.



Fits:
Porsche 911/912/930/914 1968-89 with installation tools

Front control arm rubber bushings are now available as a kit for self-installation. In addition to a complete set of 4 OEM spec rubber bushings, the kit includes our proprietary installation tools and instructions which are essential for successful installation. Use a pipe clamp or shop press to complete the install.

Restore Ride and Performance
Rubber is the choice if you want to restore factory ride and performance in a zero-maintenance solution.

Quality Design
Don't confuse Elephant Racing OEM spec control arm bushings with inferior products offered without installation tools. Those products have a loose fit to allow tool-less installation. The loose fit causes excessive bushing deformation, torsion bar rubbing, premature wear, bushing slippage, and changing corner balance. Be sure you are getting genuine Elephant Racing OEM spec bushings.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

2290000

The product you are viewing cross references to these numbers

Low-friction control arm mounts.
1 pair req'd per car.



Fits:
Porsche 911 / 912 / 930 1968-89

Non-Binding, Friction- Free Movement
Elephant Racing's proprietary-design Low-Friction Control Arm Mounts allow for free control arm movement, eliminating any potential for binding. We've corrected a key factory design limitation; our mounts self-align in all axis, becoming collinear to avoid binding as the arm moves through its range of motion.

Factory Mounts and Binding
911 series and 914 factory control arm mounts pivot allow for self-alignment in the horizontal plane only. Any misalignment in the vertical plane results in pinching and binding at the bushing that resists free movement of the control arm.
Non-colinear axis binding

Factory mounting points (stamped sheet metal) are imprecise at best and can be substantially off due to frontal impacts, pot holes, or suspension pan replacement. If the mounts are not collinear, the control arm will bind with any performance bushing compound or bearing.

Self-Aligning Low-Friction Mounts
Our Low-Friction Control Arm Mounts self-align in both the horizontal and vertical planes. The result is collinear front and rear mounts delivering smooth non-binding action. You get superior performance and a smoother ride.

Control Arm Mount Kit
Kit includes everything required to upgrade one car. Factory rear mounts are replaced with our self-aligning mounts. Factory front mounts are retained and augmented with self-aligning washers.

With this kit installed, both front and rear control arm mounts self-align in both vertical and horizontal planes. They become collinear, allowing free non-binding motion of the control arm.

Our mounts replicate the factory form factor and work in conjunction with Polybronze bearings, polyurethane, or any other hard compound bushing or bearing. Fits both aluminum and steel suspension cross-members.

For Fitting Instructions please CLICK HERE

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

2071600

The product you are viewing cross references to these numbers

Solid subframe bushing set. 12 bushings in kit. 1 kit req'd per car.



Fits:
Porsche 996 / 997

Improved Handling and Precision
Our Rear Subframe Solid Bushing kit improves handling and precision by providing geometry correction for lowered cars and eliminating deflection. Porsche recognizes these performance benefits and uses a similar solid rear subframe mounting approach on the latest GT3 street and Cup racecars.

Replaces stock rubber bushings in the rear subframe of the Porsche 996 and 997 cars, raising the subframe into the chassis 6.5mm (.25 inch).

Geometry Correction
Lowering the 996/997 provides the benefits of lower center of gravity and improved appearance. Unfortunately lowering also causes the rear suspension members to angle down as the inner links drop with the chassis and the outer links remain at wheel upright height. This downward angle harms performance.

With the suspension members angling up towards the wheel the Roll Center is lowered which causes increased chassis lean, toe and camber curves are shifted and become less optimal, static toe and camber adjustments are shifted often exceeding the range of the stock adjusters.

Our kit raises the rear subframe .25 inches (6.5mm) to help reverse the negative effects of lowering. Suspension member angles are improved and performance is enhanced. Our upper bushing fits inside the subframe, eliminating the entire thickness of the upper rubber bushing for the greatest possible geometry correction achievable from bushings alone.

Eliminate Deflection
Stock rubber bushings compress and deform under heavy cornering, braking, and acceleration loads. The compliant rubber bushings allow the entire rear subframe shift about relative to the chassis. Rear camber and toe settings wander along with the subframe making the car less predictable, less stable in turns.

Our solid bushings replace the compliant rubber and do not deform under cornering loads, keeping the subframe in position and alignment true even under heavy cornering loads. The car becomes more predictable and easier to drive fast.

Build Quality
Each bushing consists of two pieces, an upper plug and lower puck. The plug is machined from solid aluminum with knurled edges for perfect fit.

Lower puck is machined from solid steel with zinc finish for protection.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

2290035

The product you are viewing cross references to these numbers

QuickChange™ Camber Plates.
Sold per kit, 1 kit req'd per car.




Porsche 996 / 997 C2 models 1999-2012
Porsche 986 / 987 1997-12

Elephant Racing's QuickChange™ Camber plates offer true ease of adjustment. The "slider" design allows a full range of adjustment without the need for removing and rotating the plate for C2, C4, and Turbo models.

More Camber
Range of adjustment is extreme, with 19mm of added travel. This delivers over 2 degrees of added camber, allowing even DOT-R tires and slicks to produce maximum grip.

QuickChange Camber Plate for C4 and Turbo Models
The Quickchange camber plates are available for C2, C4 and Turbo models and work with stock-type springs and coilovers. They will not raise ride height when used with stock-type springs.

Higher Performance
Spherical bearings further improve performance. The spherical bearings pivot freely, but eliminate the deflection that is inherent with the factory rubber bushings. This is important for two reasons;

– The factory rubber acts as a spring in series with the strut. This rubber spring-action is completely un-damped and reduces the struts ability to control the tire contact patch. The spherical bearing allows the strut damper to do its job and control the contact patch.

– The factory rubber deflects sideways under cornering loads, causing loss of camber just when you need it most. Our spherical bearings eliminate the deflection, maintaining stable and predictable camber.

Fully Weather Sealed
The included spherical bearings are oversized, maintenance-free, and PTFE lined – they never need lubrication.
Integrated weather seals on both bottom and top of the spherical bearing extend bearing life. Dirt and water enter competing non-sealed products to accelerate bearing wear. Worse yet are bottom-only seals that can actually trap water that enters the open bearing top!

Our weather seals are fully compatible with coilovers and stock type springs.

Use Stock Springs or Coilovers
Fully compatible with stock springs and aftermarket lowering springs. Also supports coilovers that use and upper spring perch.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

2152205

The product you are viewing cross references to these numbers

QuickChange™ Camber Plates.
Sold per kit, 1 kit req'd per car.



Elephant Racing's QuickChange™ Camber plates offer true ease of adjustment. The "slider" design allows a full range of adjustment without the need for removing and rotating the plate for C2, C4, and Turbo models.

Fits:
Porsche 996/997 C4 and Turbo Models 1999-2012

More Camber
Range of adjustment is extreme, with 19mm of added travel. This delivers over 2 degrees of added camber, allowing even DOT-R tires and slicks to produce maximum grip.

QuickChange Camber Plate for C4 and Turbo Models
The Quickchange camber plates are available for C2, C4 and Turbo models and work with stock-type springs and coilovers. They will not raise ride height when used with stock-type springs.

Higher Performance
Spherical bearings further improve performance. The spherical bearings pivot freely, but eliminate the deflection that is inherent with the factory rubber bushings. This is important for two reasons;

– The factory rubber acts as a spring in series with the strut. This rubber spring-action is completely un-damped and reduces the struts ability to control the tire contact patch. The spherical bearing allows the strut damper to do its job and control the contact patch.

– The factory rubber deflects sideways under cornering loads, causing loss of camber just when you need it most. Our spherical bearings eliminate the deflection, maintaining stable and predictable camber.

Fully Weather Sealed
The included spherical bearings are oversized, maintenance-free, and PTFE lined – they never need lubrication.
Integrated weather seals on both bottom and top of the spherical bearing extend bearing life. Dirt and water enter competing non-sealed products to accelerate bearing wear. Worse yet are bottom-only seals that can actually trap water that enters the open bearing top!

Our weather seals are fully compatible with coilovers and stock type springs.

Use Stock Springs or Coilovers
Fully compatible with stock springs and aftermarket lowering springs. Also supports coilovers that use and upper spring perch.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

2152210

The product you are viewing cross references to these numbers

QuickChange™ front camber plate kit.
Sold per kit, 1 kit req'd per car.

Extend the range of camber adjustment and dial in your desired settings with ease.

These plates use high strength hardened steel spherical bearings and are direct replacements for the factory plates. The Teflon lined spherical bearings used in our kit are maintenance-free and require no supplemental lubrication. Included seals prevent contamination from water or grime, thus extending bearing life.

Fits:
Porsche 964 1990-94 / 993 1995-98 Front camber plate 14mm spacers

Fully Weather Sealed:
We've designed in weather seals on the top and bottom to keep dirt out and extend product life. This is the only camber plate suitable for street or extended track use. Dirt and water contaminate ordinary products and accelerate wear.

This camber plate is intended to be used with a non-factory upper spring perch and spring. This kit is suited to work perfectly with Von Coilover systems or other similar solutions.

Please note: please contact us if you wish to use this camber plate kit in conjunction with factory or lowering springs.

Ease of Camber Adjustment
Indices on the camber plate allow measured changes without setup tools.

Extended Caster
These plates deliver the same caster as the 993 for enhance camber gain when turning.

Improved Shock / Coilover Performance
Spherical bearings further improve performance. The spherical bearings pivot freely and eliminate the deflection that is inherent with the factory rubber bushings. This is important for two reasons;

– The factory rubber acts as a spring in series with the strut. This rubber spring-action is completely un-damped and reduces the struts ability to control the tire contact patch. The spherical bearing allows the strut damper to do its job and control the contact patch.

– The factory rubber deflects sideways under cornering loads, causing loss of camber just when you need it most. Our spherical bearings eliminate the deflection, maintaining stable and predictable camber.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

2152202

The product you are viewing cross references to these numbers

Front Adjustable Drop Links
Sold per kit, 1 kit req'd per car.



✓ Maintenance-free precision rod ends
✓ Weather-sealed
✓ Direct Bolt-on replacement


Porsche 964 C2 / C4 1989-94

The ideal swaybar is completely unloaded at static ride height. Stock drops links almost always preload the swaybar since the car doesn't sit perfectly level due to asymmetries such as driver weight.Our front and rear adjustable-length drop links for C4/C2 allow you to eliminate preload of the swaybar for maximum performance.

A preloaded swaybar shifts the weight carried by each of the tires, increasing grip on weighted tires at the expense of decreasing grip on un-weighted tires. This shifted weight/grip causes uneven handling in left and right turns, and premature brake lockup since the less-loaded tire locks up first. Preload can be completely eliminated by adjusting drop link length and swaybar performance optimized.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

2271018

The product you are viewing cross references to these numbers

QuickChange™ Torsion Bars, REAR
Sold per kit, 1 kit req'd per car.



Fits:
Porsche 911/912/930/914 '65-'86
Porsche 356 A/B '48-'65 (Pre-A, C and CS Read Notes),
Porsche 944/968/924 '76-'95 w/ QuickChange Spring Plates

PLEASE NOTE: sizes 34mm and 36mm are not applicable for 944, 968 and 924 models)

QuickChange Torsion Bars are Plated & Plugged and include a female threaded end that you can engage with a bolt to use as a handle for easier extraction / insertion.

Use the rears bars in combination with our QuickChange™ Spring Plate products for fast torsion bar swapping and re-indexing. QuickChange™ Torsion Bars can be extracted through the QuickChange™ Spring Plate without removing any bolts. Alignment settings are maintained. You don't even need to remove the wheel from the car. Changing torsion bars is a 5 minute per side operation!

A QuickChange™ Insert is available separately for converting your existing hollow torsion bars.

QuickChange™ Torsion Bars make it easy to dislodge a stuck bar, and thereby offer benefits even when used on the front and with factory spring plates (factory spring do not allow the bars to be extracted without removing the plates).

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

21020

The product you are viewing cross references to these numbers

QuickChange™ Torsion Bars, REAR
Sold per kit, 1 kit req'd per car.



Fits:
for G50 Transmission
Porsche 911 / 930 1987-89

QuickChange Torsion Bars are Plated & Plugged and include a female threaded end that you can engage with a bolt to use as a handle for easier extraction / insertion.

Use the rears bars in combination with our QuickChange™ Spring Plate products for fast torsion bar swapping and re-indexing. QuickChange™ Torsion Bars can be extracted through the QuickChange™ Spring Plate without removing any bolts. Alignment settings are maintained. You don't even need to remove the wheel from the car. Changing torsion bars is a 5 minute per side operation!

A QuickChange™ Insert is available separately for converting your existing hollow torsion bars.

QuickChange™ Torsion Bars make it easy to dislodge a stuck bar, and thereby offer benefits even when used on the front and with factory spring plates (factory spring do not allow the bars to be extracted without removing the plates).

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

21021

The product you are viewing cross references to these numbers

QuickChange™ Torsion Bars, FRONT
Sold per kit, 1 kit req'd per car.

Fits:
Porsche 911/912/930 1965-89
Porsche 914 1970-76

QuickChange Torsion Bars are Plated & Plugged and include a female threaded end that you can engage with a bolt to use as a handle for easier extraction / insertion.

Use the rears bars in combination with our QuickChange™ Spring Plate products for fast torsion bar swapping and re-indexing. QuickChange™ Torsion Bars can be extracted through the QuickChange™ Spring Plate without removing any bolts. Alignment settings are maintained. You don't even need to remove the wheel from the car. Changing torsion bars is a 5 minute per side operation!

A QuickChange™ Insert is available separately for converting your existing hollow torsion bars.

QuickChange™ Torsion Bars make it easy to dislodge a stuck bar, and thereby offer benefits even when used on the front and with factory spring plates (factory spring do not allow the bars to be extracted without removing the plates).

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

209202

The product you are viewing cross references to these numbers

QuickChange™ Spring Plate Kit.
Sold per kit, 1 kit req'd per car.

Fits:
Porsche 911/912/930 1965-1986

Available In Three Configurations
• For '65-'68 911/912, Short Wheel Base
• For '69-'86 911/912, '75-'86 930, Long Wheel Base
• For '69-'86 911/912, '75-'86 930, Splined Hub Kit


Change Torsion Bars and Adjust Ride Height

QuickChange spring plates make fast-work of torsion bar re-indexing and replacement. Screw-type adjuster makes corner balancing and ride height adjustment a breeze. Pairs the high quality of the factory design with ease of servicing.

• 5 minute torsion bar changes
• Fast and easy ride-height adjustment
• Accepts standard bushings

Setup is fast and easy

If you've ever re-indexed torsion bars to correct ride height, you can really appreciate the benefits of QuickChange. Used in combination with our QuickChange Torsion Bars and Polybronze bearings, this spring plate allows rapid replacement or re-indexing of torsion bars.

QuickChange Torsion Bar Changeout

QuickChange Torsion Bars can be extracted through the QuickChange Spring Plate without removing any bolts. Alignment settings are maintained. You don't even need to remove the wheel from the car. Changing torsion bars is a 5 minute per side operation!

Unlike other aftermarket spring plates, QuickChange Spring Plates bolt the plates together. This prevents the plates "halves" from sliding against each other and eliminates failures and metallic clicking noises common with competing products.

Can be used with any torsion bar and bushing that fits factory spring plates – not included – however QuickChange Torsion bars and PolyBronze Bearings are required to use torsion bar extraction features.

Kits for '69-'86 long wheel base cars include a screw type height adjuster. Kits for '65-'68 short wheel base cars use an eccentric bolt height adjuster for improved tire clearance.

To add QuickChange functionality to your existing set of '77-'86 factory adjustable spring plates or ASP, you can order the Splined Hub separately.

Splined Hub Kits

The Splined Hub Kit includes the small plate and adjuster hardware to mate with the large plate from your donor set of factory adjustable spring plates, or the ASP. Order one kit per car.

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

208090

The product you are viewing cross references to these numbers

Spring Plate Reinforcement Kit
Sold per kit, 1 kit req'd per car.

Fits:
Porsche 911/912/930 1965-89

Repair or prevent spring plate mounts from cracking.

Repair or prevent spring plate mounts from cracking
Spring Plate Mount Reinforcement Panels will help prevent or repair the common problem of cracked spring plate cover mounts resulting from worn, deformed, or stuck bushings in the cover.

Elephant Racing Rear Spring Plate Mount Reinforcement Panels are precision laser-cut and formed panels from 18 gauge steel. These panels distribute the torsion bar and spring plate loads into the torsion tube housing and multi-layer sheet metal just beyond the original mounting boss locations.

Excess heat during the welding process will tend to distort the sheet metal moving the mounting studs out of alignment. The included Mounting Stud Alignment Panel will help maintain their original spacing allowing for much easier reassembly.

At this time, you may also be interested in replacing your bushings or upgrade to Elephant Racing's PolyBronze spring plate bushings.

Please note: Welding is required to install properly

Related reference numbers
Related, superseded, cross reference or alternative numbers for comparison.

2061003

The product you are viewing cross references to these numbers